1stGen.org

THE place for 1st gens

Skip to content

4 guage pod holder

How the engine works

Moderators: Greenleaf, KTA, BC847, Richie O

Post a reply

4 guage pod holder

Postby Power Ram Man » Mon Mar 26, 2012 6:27 pm

Was wondering if anyone knew where i could get one of those 4 pillar gauge pods for my truck didnt no if you could still get them thanks
92 3/4 Cummins with coverted getrag 5 speed, 4x4 PODS,3200 Gov spring,16cm housing, 4inch exhuast homemade downpipe, water meth,hx35 turbo,5 inch stainless intake with AFE filter, fuel turned up, timing bumped boost,pyro guages, Denny T fuel pin,coolertubz,piston lift pump
Power Ram Man
fuel screw!!!!
 
Posts: 144
Joined: Mon Apr 23, 2007 7:11 pm
Location: North Carolina
Top

Re: 4 guage pod holder

Postby peobryant » Tue Mar 27, 2012 10:41 am

The only 4 gauge pillar pods I know of are custom made (I bought one from a man off here, but he no longer makes them) but I have heard of people stacking the 2 gauge pillar pods together. The viewing angle may not be ideal though.
Parker
1991 Dodge Ram D350, Cummins Turbo Diesel, A518
1972 Mercedes-Benz 220D, OM615 Diesel, 4 Speed Manual
User avatar
peobryant
14mm rotor
 
Posts: 1946
Joined: Thu Dec 27, 2007 1:07 am
Location: Goshen, Ky
Top

Re: 4 guage pod holder

Postby Power Ram Man » Tue Mar 27, 2012 2:40 pm

Whats the guys name that used to make them
92 3/4 Cummins with coverted getrag 5 speed, 4x4 PODS,3200 Gov spring,16cm housing, 4inch exhuast homemade downpipe, water meth,hx35 turbo,5 inch stainless intake with AFE filter, fuel turned up, timing bumped boost,pyro guages, Denny T fuel pin,coolertubz,piston lift pump
Power Ram Man
fuel screw!!!!
 
Posts: 144
Joined: Mon Apr 23, 2007 7:11 pm
Location: North Carolina
Top

Re: 4 guage pod holder

Postby CumminsPower59 » Tue Mar 27, 2012 8:04 pm

SOOT4BRAINS is the user name of the fellow that use to make them...
Ike

91 W350 SRW, 3.07's, NV4500, 370's, THD LPPP, Super HX40, 2nd gen IC swap, BHAF, Isspro's, 2" lift, 285's on 3rd gen 17"'s.
04 VW Jetta Wagon TDI 5speed
CumminsPower59
14mm rotor
 
Posts: 3203
Joined: Mon Feb 25, 2008 8:04 am
Location: The Hawkeye State of 'Murica!
Top

Re: 4 guage pod holder

Postby Power Ram Man » Wed Mar 28, 2012 5:04 am

The guys name is not on the members list
92 3/4 Cummins with coverted getrag 5 speed, 4x4 PODS,3200 Gov spring,16cm housing, 4inch exhuast homemade downpipe, water meth,hx35 turbo,5 inch stainless intake with AFE filter, fuel turned up, timing bumped boost,pyro guages, Denny T fuel pin,coolertubz,piston lift pump
Power Ram Man
fuel screw!!!!
 
Posts: 144
Joined: Mon Apr 23, 2007 7:11 pm
Location: North Carolina
Top

Re: 4 guage pod holder

Postby CumminsPower59 » Wed Mar 28, 2012 5:20 am

I don't know the whole story, but from what I read, he was making those pillar pods in his fathers garage, and apparently his father wasn't pleased because of the dust and what not. I remember reading a while back that he was gonna get his own place and start making them again, but that was 2010. He is still a member here. Kinda sucks that he hasn't made any for a while, I wanted one pretty badly... :(

The thread on those pods is in the member endeavors section...
viewtopic.php?f=14&t=4323
Ike

91 W350 SRW, 3.07's, NV4500, 370's, THD LPPP, Super HX40, 2nd gen IC swap, BHAF, Isspro's, 2" lift, 285's on 3rd gen 17"'s.
04 VW Jetta Wagon TDI 5speed
CumminsPower59
14mm rotor
 
Posts: 3203
Joined: Mon Feb 25, 2008 8:04 am
Location: The Hawkeye State of 'Murica!
Top
Post a reply

Return to Engine

Who is online

Users browsing this forum: No registered users and 59 guests

Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group