1stGen.org

THE place for 1st gens

Skip to content

Need an ip

How the engine works

Moderators: Greenleaf, KTA, BC847, Richie O

Post a reply

Need an ip

Postby skilletky » Thu Mar 01, 2012 6:45 pm

I am gonna buy a new ip or have mine rebuilt. Gonna stick with a 12mm. Who should I buy one from or who should I have rebuild mine?
92 d350, arp's, orings, 150lb springs, 4200 gsk ,ground pin ,64/71/14 ,ddp inj's, ats manifold, tim's tubez, ats trans, FASS, locker, timing + a tooth, bcdd intake

2001 2wd rclb dually 5sp, smarty, Bluechip FMS, TS MVP, 57/75 twins, stainless diesel pipe kit, valair clutch, airdog 150, DFI SAC 7x.014's, cheap a$$ intake, ARP studs, oringed head, CPP 115# springs
User avatar
skilletky
14mm rotor
 
Posts: 1070
Joined: Thu Jan 10, 2008 5:49 pm
Location: northern ky
Top

Re: Need an ip

Postby skilletky » Fri Mar 02, 2012 5:33 pm

Any opinions?
92 d350, arp's, orings, 150lb springs, 4200 gsk ,ground pin ,64/71/14 ,ddp inj's, ats manifold, tim's tubez, ats trans, FASS, locker, timing + a tooth, bcdd intake

2001 2wd rclb dually 5sp, smarty, Bluechip FMS, TS MVP, 57/75 twins, stainless diesel pipe kit, valair clutch, airdog 150, DFI SAC 7x.014's, cheap a$$ intake, ARP studs, oringed head, CPP 115# springs
User avatar
skilletky
14mm rotor
 
Posts: 1070
Joined: Thu Jan 10, 2008 5:49 pm
Location: northern ky
Top

Re: Need an ip

Postby ellis93 » Fri Mar 02, 2012 8:28 pm

Folks I use
http://www.mylexinternational.com/

Call them and ask for kenny or shawn in the pump shop. Shawn is the builder there,so he'd be the most knowledgable.
93 D250 ,5 speed,4.11s,k&n autometer tach pyro trans boost guages,GDS 60mm h1c 14cm,honed 5x10,hplp/reg,1/8 timing,M+H M2 fuel pin, tims cooler tubz
User avatar
ellis93
14mm rotor
 
Posts: 7762
Joined: Wed Feb 17, 2010 3:16 pm
Location: lucedale,mississippi
Top

Re: Need an ip

Postby skilletky » Fri Mar 02, 2012 9:09 pm

Thank you sir. I'm gomna give them a call Monday.
92 d350, arp's, orings, 150lb springs, 4200 gsk ,ground pin ,64/71/14 ,ddp inj's, ats manifold, tim's tubez, ats trans, FASS, locker, timing + a tooth, bcdd intake

2001 2wd rclb dually 5sp, smarty, Bluechip FMS, TS MVP, 57/75 twins, stainless diesel pipe kit, valair clutch, airdog 150, DFI SAC 7x.014's, cheap a$$ intake, ARP studs, oringed head, CPP 115# springs
User avatar
skilletky
14mm rotor
 
Posts: 1070
Joined: Thu Jan 10, 2008 5:49 pm
Location: northern ky
Top

Re: Need an ip

Postby bgilbert » Sat Mar 03, 2012 7:23 am

KTA. He's probly right in your backyard.
Bill Gilbert
85 D350 crew with 90 6BT intercooled Getrag 3.07's
93 D350 single cab Getrag 3.54's.
bgilbert
14mm rotor
 
Posts: 2253
Joined: Wed Jan 03, 2007 5:04 pm
Location: Terre Haute, Indiana
Top

Re: Need an ip

Postby skilletky » Sat Mar 03, 2012 8:44 am

That's true. I didn't even think of asking him.
92 d350, arp's, orings, 150lb springs, 4200 gsk ,ground pin ,64/71/14 ,ddp inj's, ats manifold, tim's tubez, ats trans, FASS, locker, timing + a tooth, bcdd intake

2001 2wd rclb dually 5sp, smarty, Bluechip FMS, TS MVP, 57/75 twins, stainless diesel pipe kit, valair clutch, airdog 150, DFI SAC 7x.014's, cheap a$$ intake, ARP studs, oringed head, CPP 115# springs
User avatar
skilletky
14mm rotor
 
Posts: 1070
Joined: Thu Jan 10, 2008 5:49 pm
Location: northern ky
Top
Post a reply

Return to Engine

Who is online

Users browsing this forum: No registered users and 22 guests

Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group
cron