Cooling fan blades

How the engine works

Moderators: Greenleaf, KTA, BC847, Richie O

Cooling fan blades

Postby walkerkd » Wed Sep 23, 2015 6:45 pm

I saw a fan without a clutch going for 400 bucks yea 400 bucks..... Is this right????
walkerkd
fuel screw!!!!
 
Posts: 56
Joined: Fri Jul 29, 2011 3:18 pm

Re: Cooling fan blades

Postby thrashingcows » Wed Sep 23, 2015 8:26 pm

Yup....the supply of NOS 1st gen cooling fan blades dried up years ago. 2nd Gen units were a direct swap, but the last NOS ones are pulling big bucks now days. Even used ones, 1st and 2nd Gen units are getting 250-400!

I bought a NOS 2nd Gen unit about 5 years ago now...Came in the Mopar box and everything. Think I paid $125 for it at the time. ;)
1984/93 Dodge Crewcab, W350, 1 Ton SRW, long box, 330K Km's, M&H spacer, 366 spring, fuel pin to deep side, 14cm housing, Piston LP, PS IC, Isspro Boost, Pyro and tach, NV4500, 29 spline NP205, 3.54's.


Check out the build....http://www.dieseltruckresource.com/dev/ ... 05923.html
thrashingcows
14mm rotor
 
Posts: 575
Joined: Wed Nov 02, 2011 12:00 am

Re: Cooling fan blades

Postby CumminsPower59 » Thu Sep 24, 2015 5:16 am

All second gen fans the same? Reason I ask is I have a low mileage take off that was on an 02 24v. Been sitting around, it has gotten close to the scrap pile a few times :/
Ike

91 W350 SRW, 3.07's, NV4500, 370's, THD LPPP, Super HX40, 2nd gen IC swap, BHAF, Isspro's, 2" lift, 285's on 3rd gen 17"'s.
04 VW Jetta Wagon TDI 5speed
CumminsPower59
14mm rotor
 
Posts: 3203
Joined: Mon Feb 25, 2008 8:04 am
Location: The Hawkeye State of 'Murica!
Top

Re: Cooling fan blades

Postby ellis93 » Thu Sep 24, 2015 6:31 am

Don't do it Ike,it works fine.
93 D250 ,5 speed,4.11s,k&n autometer tach pyro trans boost guages,GDS 60mm h1c 14cm,honed 5x10,hplp/reg,1/8 timing,M+H M2 fuel pin, tims cooler tubz
User avatar
ellis93
14mm rotor
 
Posts: 7761
Joined: Wed Feb 17, 2010 3:16 pm
Location: lucedale,mississippi
Top

Re: Cooling fan blades

Postby CumminsPower59 » Thu Sep 24, 2015 7:08 am

Well, I know that. I have a bad habit of keeping old stuff around that I "may" use...but if I can use it in the future for The Pile, then I will. I had to build shelves down one whole wall in my ancient garage just to store a lot of the junk that I have...and I still have just enough room to park my bike in the garage. No way I could ever work out of it, I'm back to working on an even smaller outside concrete pad than when I rebuilt my truck two years ago :? I am fixing to build even more shelves all the way around, except for the side that my work bench is on, but it will have an overhead one that I can attach lighting to underneath to light up the bench area. By the time I get around to moving again and having a proper work area, I'll be too damn old to do anything anymore :mad:
Ike

91 W350 SRW, 3.07's, NV4500, 370's, THD LPPP, Super HX40, 2nd gen IC swap, BHAF, Isspro's, 2" lift, 285's on 3rd gen 17"'s.
04 VW Jetta Wagon TDI 5speed
CumminsPower59
14mm rotor
 
Posts: 3203
Joined: Mon Feb 25, 2008 8:04 am
Location: The Hawkeye State of 'Murica!
Top


Return to Engine

Who is online

Users browsing this forum: No registered users and 12 guests

cron