1stGen.org

THE place for 1st gens

Skip to content

14 mm head

Off topic/not diesel related

Moderators: Greenleaf, BC847, Richie O

Post a reply

14 mm head

Postby skilletky » Sun Sep 25, 2011 6:21 pm

http://cgi.ebay.com/ebaymotors/Dodge-Cu ... 336c7e129b

figured someone may be interested. says it made by the same company that made the factory 12 mm head. was there ever a factory 14mm ve available in other apps?
92 d350, arp's, orings, 150lb springs, 4200 gsk ,ground pin ,64/71/14 ,ddp inj's, ats manifold, tim's tubez, ats trans, FASS, locker, timing + a tooth, bcdd intake

2001 2wd rclb dually 5sp, smarty, Bluechip FMS, TS MVP, 57/75 twins, stainless diesel pipe kit, valair clutch, airdog 150, DFI SAC 7x.014's, cheap a$$ intake, ARP studs, oringed head, CPP 115# springs
User avatar
skilletky
14mm rotor
 
Posts: 1070
Joined: Thu Jan 10, 2008 5:49 pm
Location: northern ky
Top

Re: 14 mm head

Postby bgilbert » Mon Sep 26, 2011 1:20 pm

Have to have KTA comment on that. The ebay seller has a link to KTA's youtube dyno run video... Says same company that made his etc...
Bill Gilbert
85 D350 crew with 90 6BT intercooled Getrag 3.07's
93 D350 single cab Getrag 3.54's.
bgilbert
14mm rotor
 
Posts: 2253
Joined: Wed Jan 03, 2007 5:04 pm
Location: Terre Haute, Indiana
Top

Re: 14 mm head

Postby dazedandconfused » Mon Sep 26, 2011 6:20 pm

I was wondering if it was a KTA special myself.
Big Andy
1983 Dodge D150 that has been repowered with a 93 Cummins/518 running gear AKA The Ugly Duck! I would much rather build them then buy them.[
User avatar
dazedandconfused
14mm rotor
 
Posts: 6119
Joined: Thu Apr 05, 2007 6:25 pm
Location: Walton, Kentucky
Top

Re: 14 mm head

Postby skilletky » Mon Sep 26, 2011 8:31 pm

I was thinking it was a kta unit. I want it, but i just boughtt studs and another head that is about to get sent out for oringing some im kinda low on funds at the moment :-(
92 d350, arp's, orings, 150lb springs, 4200 gsk ,ground pin ,64/71/14 ,ddp inj's, ats manifold, tim's tubez, ats trans, FASS, locker, timing + a tooth, bcdd intake

2001 2wd rclb dually 5sp, smarty, Bluechip FMS, TS MVP, 57/75 twins, stainless diesel pipe kit, valair clutch, airdog 150, DFI SAC 7x.014's, cheap a$$ intake, ARP studs, oringed head, CPP 115# springs
User avatar
skilletky
14mm rotor
 
Posts: 1070
Joined: Thu Jan 10, 2008 5:49 pm
Location: northern ky
Top

Re: 14 mm head

Postby oldestof11 » Tue Sep 27, 2011 9:01 am

I am definitely watching this one. I have some money.... :twisted:
Jon
93 D250~ Mismatch of cheap parts, trying to look fast going slow
User avatar
oldestof11
14mm rotor
 
Posts: 4147
Joined: Tue Apr 24, 2007 4:46 pm
Location: Northern Illinois
Top

Re: 14 mm head

Postby dazedandconfused » Sun Oct 02, 2011 9:03 am

So did anybody on here get it?
Big Andy
1983 Dodge D150 that has been repowered with a 93 Cummins/518 running gear AKA The Ugly Duck! I would much rather build them then buy them.[
User avatar
dazedandconfused
14mm rotor
 
Posts: 6119
Joined: Thu Apr 05, 2007 6:25 pm
Location: Walton, Kentucky
Top

Re: 14 mm head

Postby 1arock » Sun Oct 02, 2011 10:21 am

I got outbid in the last minute.
92W250 w/a 68D100 skin,tach, pyro, boost, trans temp guages, rebuilt a518 w/a PTC converter, 4in muffeled exhaust, 3200 gov spring, he351cw,M@H dynamic timing, 5x12s,M@H M3 pin, pump jacked with, 3.54s, 6+ lift, 14.5x36r rubber,nearly done,"What was I thinking?"
User avatar
1arock
fuel screw!!!!
 
Posts: 107
Joined: Thu Feb 03, 2011 1:49 pm
Location: Scott City MO
Top

Re: 14 mm head

Postby oldestof11 » Sun Oct 02, 2011 10:26 am

When it went over $200, I stopped watching. :x I was hoping for a cheapy. :lol:
Jon
93 D250~ Mismatch of cheap parts, trying to look fast going slow
User avatar
oldestof11
14mm rotor
 
Posts: 4147
Joined: Tue Apr 24, 2007 4:46 pm
Location: Northern Illinois
Top

Re: 14 mm head

Postby dazedandconfused » Sun Oct 02, 2011 10:34 am

It was a KTA special. He said he bought it from Brian Years ago.
Big Andy
1983 Dodge D150 that has been repowered with a 93 Cummins/518 running gear AKA The Ugly Duck! I would much rather build them then buy them.[
User avatar
dazedandconfused
14mm rotor
 
Posts: 6119
Joined: Thu Apr 05, 2007 6:25 pm
Location: Walton, Kentucky
Top

Re: 14 mm head

Postby Mark Nixon » Sun Oct 02, 2011 10:41 am

I don't understand the interest in them, myself.

Unless you do big mods, you can't get the fuel to it to help it live, the transfer pump in a stock VE won't feed it enough to get more RPMS with enough fuel to cool it.
It destroys internal parts, especially if you jump to a 4mm cam plate, even the guys running them have had issues with them not holding up.
Even Rockentech admonishes that it won't live.

IMO it's a very MARGINAL upgrade at the best, just in what I have read and heard.

To me, a 13mm would probably be just the middle ground a guy would need, but since "superstition" runs our lives, 13 is unlucky. :roll:

Otherwise P-Pump it if you really "Desire The Black Fire".

Mark.
Mark Nixon
 
Top

Re: 14 mm head

Postby 1arock » Sun Oct 02, 2011 1:47 pm

There is a local "Know it all, cause I read it on the internet" jerk wad who never owned a diesel anything, before his new $65,000 duramax, running around poor mouthing the ve pump. I thought I might build up a spare fuel system just to teach him some humility. Rocky
92W250 w/a 68D100 skin,tach, pyro, boost, trans temp guages, rebuilt a518 w/a PTC converter, 4in muffeled exhaust, 3200 gov spring, he351cw,M@H dynamic timing, 5x12s,M@H M3 pin, pump jacked with, 3.54s, 6+ lift, 14.5x36r rubber,nearly done,"What was I thinking?"
User avatar
1arock
fuel screw!!!!
 
Posts: 107
Joined: Thu Feb 03, 2011 1:49 pm
Location: Scott City MO
Top

Re: 14 mm head

Postby Mark Nixon » Sun Oct 02, 2011 8:38 pm

If you feel you MUST have one, there's a 14mm RockenTech H&R posted in the For Sale on here.

viewtopic.php?f=6&t=11274

Mark.
Mark Nixon
 
Top
Post a reply

Return to Lounge

Who is online

Users browsing this forum: No registered users and 4 guests

Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group