1stGen.org

THE place for 1st gens

Skip to content

New from Houston area

Stop in and say hi

Moderators: Greenleaf, BC847, Richie O

Post a reply

New from Houston area

Postby quiksilver » Wed Oct 31, 2012 8:56 pm

I've had my 1991.5 w250 for a few years but just now focusing on the performance end of it all. Went for the facelift after i got it. Just have the basics done on it as far as performance, 4" tbe, dennyt stg II and screw turned up. The VE just recently started leaking like a sift. Rebuild or P pump the goat?
Image
Image
Image
quiksilver
smoke screw?
 
Posts: 2
Joined: Wed Oct 24, 2012 7:16 pm
Top

Re: New from Houston area

Postby ellis93 » Thu Nov 01, 2012 3:39 am

Welcome! Nice truck
93 D250 ,5 speed,4.11s,k&n autometer tach pyro trans boost guages,GDS 60mm h1c 14cm,honed 5x10,hplp/reg,1/8 timing,M+H M2 fuel pin, tims cooler tubz
User avatar
ellis93
14mm rotor
 
Posts: 7761
Joined: Wed Feb 17, 2010 3:16 pm
Location: lucedale,mississippi
Top

Re: New from Houston area

Postby tampabayBill » Thu Nov 01, 2012 6:06 am

Welcome !! I'm in Beaumont and get over to the League City area often, where are you ?
93D250 CC LE, 62/65/13 S300, PDR cam,DDP3's, B&D IP, 366 GSK, M3 & timing device, Air Dog 150, Cooler tubes, 3 piece manifold, BHAF & 4" tbe, ported & O ringed, ARP studs, 60# springs 47RH & 3 disc conv., fp, aux trans cooler, fluid damper, 3:54 D70 w/trac-lok, rear sway bar, gauges = egt,boost, tach, 47RH & diff. temps.
Twins coming soon!
tampabayBill
fuel screw!!!!
 
Posts: 293
Joined: Sat Oct 09, 2010 7:51 am
Location: New Port Richey, Fla.
Top

Re: New from Houston area

Postby JD91 » Thu Nov 01, 2012 3:12 pm

welcome!!! nice to see some more Texans on here
91 w250 RC, getrag, 4in turbo back diamond eye
93 D350 CC, getrag, 4in diamond eye, 60# springs,3200 gov,arp's,fass 150,fass sump, BD SUPER B 58MM, 5x14 sticks, M&H timing spacer, cut fuel pin,valair clutch, auto meter pyro & boost......she screams!!
91.5 d350 RC, getrag, cut fuel pin, no bed lol "the beater"
75 dodge club cab swb flat bed 4x4 "gasser" on 37's
User avatar
JD91
fuel screw!!!!
 
Posts: 105
Joined: Mon Oct 17, 2011 6:21 pm
Location: Castroville, TX
Top

Re: New from Houston area

Postby oldestof11 » Thu Nov 01, 2012 4:05 pm

Rebuild is not expensive, the p pump swap is going to run you up a bit.
Jon
93 D250~ Mismatch of cheap parts, trying to look fast going slow
User avatar
oldestof11
14mm rotor
 
Posts: 4147
Joined: Tue Apr 24, 2007 4:46 pm
Location: Northern Illinois
Top

Re: New from Houston area

Postby quiksilver » Thu Nov 01, 2012 7:08 pm

I am just north of Houston in Conroe. Thanks for the welcome guys! I think i am just going to rebuild the ve for now. Maybe one day haha!
quiksilver
smoke screw?
 
Posts: 2
Joined: Wed Oct 24, 2012 7:16 pm
Top

Re: New from Houston area

Postby dazedandconfused » Fri Nov 02, 2012 2:57 am

Welcome
Big Andy
1983 Dodge D150 that has been repowered with a 93 Cummins/518 running gear AKA The Ugly Duck! I would much rather build them then buy them.[
User avatar
dazedandconfused
14mm rotor
 
Posts: 6119
Joined: Thu Apr 05, 2007 6:25 pm
Location: Walton, Kentucky
Top
Post a reply

Return to Welcome

Who is online

Users browsing this forum: No registered users and 28 guests

Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group