1stGen.org

THE place for 1st gens

Skip to content

hello

Stop in and say hi

Moderators: Greenleaf, BC847, Richie O

Post a reply

hello

Postby dieseloutlaw » Fri May 24, 2013 12:50 pm

my w250's
Image
Image
Image
dieseloutlaw
smoke screw?
 
Posts: 4
Joined: Sun May 27, 2012 6:33 pm
Top

Re: hello

Postby dazedandconfused » Fri May 24, 2013 1:26 pm

That 89-90 is a sharp truck!
Big Andy
1983 Dodge D150 that has been repowered with a 93 Cummins/518 running gear AKA The Ugly Duck! I would much rather build them then buy them.[
User avatar
dazedandconfused
14mm rotor
 
Posts: 6119
Joined: Thu Apr 05, 2007 6:25 pm
Location: Walton, Kentucky
Top

Re: hello

Postby ellis93 » Fri May 24, 2013 3:42 pm

dazedandconfused wrote:That 89-90 is a sharp truck!


Yes....yes it is 8)
93 D250 ,5 speed,4.11s,k&n autometer tach pyro trans boost guages,GDS 60mm h1c 14cm,honed 5x10,hplp/reg,1/8 timing,M+H M2 fuel pin, tims cooler tubz
User avatar
ellis93
14mm rotor
 
Posts: 7761
Joined: Wed Feb 17, 2010 3:16 pm
Location: lucedale,mississippi
Top

Re: hello

Postby RCCUMMINS89 » Fri May 24, 2013 4:21 pm

Welcome
89 RC on shortened 92 diesel frame - NV4500 w/dual disc/4.10s on 37s. - Self built pump, "hot screw", lots of timing, True high volume low pressure lift pump, 62fmw/68/.7gated, 77lpm SAC Inj., Studs/O-rings,- 423/1220 Mustang - 11/16/2013 http://www.TheHungryDiesel.com full line dealer, if you don't see it please ask.
RCCUMMINS89
14mm rotor
 
Posts: 4826
Joined: Mon Oct 03, 2011 4:19 pm
Location: Spirit Lake, ID
Top

Re: hello

Postby CumminsPower59 » Sun May 26, 2013 9:18 am

Welcome!
Ike

91 W350 SRW, 3.07's, NV4500, 370's, THD LPPP, Super HX40, 2nd gen IC swap, BHAF, Isspro's, 2" lift, 285's on 3rd gen 17"'s.
04 VW Jetta Wagon TDI 5speed
CumminsPower59
14mm rotor
 
Posts: 3203
Joined: Mon Feb 25, 2008 8:04 am
Location: The Hawkeye State of 'Murica!
Top

Re: hello

Postby Tacoclaw » Sun May 26, 2013 9:24 am

Oh man, I'm gonna need to borrow one of Jon's discount paper towels to clean up over that '90. That thing is legit!

Welcome. 8)
1990 W250 4x4
Rattles, growls, whistles, and whines.
User avatar
Tacoclaw
14mm rotor
 
Posts: 4108
Joined: Wed Mar 11, 2009 7:50 am
Location: Cheshire, OH
Top

Re: hello

Postby cmann250 » Sun May 26, 2013 10:33 am

Well, it's obvious you are not from the Midwest. :lol: I see the California plates. That '90 is CLEAN.

Welcome.
Caleb, Certified Shade Tree Mechanic Extraordinaire :mrgreen:
The 1stgen.org black sheep

"Whatever!" - Coach Jerry Smith
cmann250
14mm rotor
 
Posts: 4059
Joined: Fri May 20, 2011 5:25 pm
Location: Lafayette, IN
Top

Re: hello

Postby Tacoclaw » Sun May 26, 2013 10:52 am

What axle is in the rear of the '90?
1990 W250 4x4
Rattles, growls, whistles, and whines.
User avatar
Tacoclaw
14mm rotor
 
Posts: 4108
Joined: Wed Mar 11, 2009 7:50 am
Location: Cheshire, OH
Top

Re: hello

Postby rockbuggy4x4 » Wed May 29, 2013 11:11 am

Welcome.
Jimmy
--> '85 cab w/ '89 engine and trans stock with minor pump tweaks and a flatbed. **soon to get lots of goodies**
--> '95 jimmy not so stock

Image
rockbuggy4x4
fuel screw!!!!
 
Posts: 230
Joined: Sun Apr 07, 2013 4:15 pm
Location: Hazleton, PA
Top
Post a reply

Return to Welcome

Who is online

Users browsing this forum: No registered users and 19 guests

Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group