1stGen.org • View topic - Lifting front end up

Lifting front end up

Moderators: Greenleaf, BC847, Richie O

6 posts • Page 1 of 1

Lifting front end up

by Tsbourne09 » Tue Nov 01, 2011 9:20 pm

Any ideas on raising my front end up on my 203k mile d250 with factory old coil springs? Where to get spacers and/or new springs?

93 D250- pump maxed, 3800 spring, hx35, denny T pump top, 7x.015 injectors, timing+, Coolertubz, raptor 150, boost nipple, 4" DP to 6" aussie stacks, built tranny, asa intake, DNR tps, more HP mods, isspro boost, fuel pressure, egt, tranny temp, 5k tach, chrome and powder coating here & there.
Not On Yet: 60#VS
http://s1130.photobucket.com/albums/m53 ... 20Uploads/

Tsbourne09: fuel screw!!!!; Posts: 337; Joined: Sun Aug 14, 2011 8:56 pm

Re: Lifting front end up

by ellis93 » Wed Nov 02, 2011 4:38 am

If you like the ride quality you have now go for spacers, springs will be pretty stiff especially the moog heavy duty springs. Dig thru this
http://www.dieseltruckresource.com/dev/ ... 02027.html

93 D250 ,5 speed,4.11s,k&n autometer tach pyro trans boost guages,GDS 60mm h1c 14cm,honed 5x10,hplp/reg,1/8 timing,M+H M2 fuel pin, tims cooler tubz

ellis93: 14mm rotor; Posts: 7762; Joined: Wed Feb 17, 2010 3:16 pm; Location: lucedale,mississippi

Re: Lifting front end up

by Tsbourne09 » Wed Nov 02, 2011 2:49 pm

Thank you!!

93 D250- pump maxed, 3800 spring, hx35, denny T pump top, 7x.015 injectors, timing+, Coolertubz, raptor 150, boost nipple, 4" DP to 6" aussie stacks, built tranny, asa intake, DNR tps, more HP mods, isspro boost, fuel pressure, egt, tranny temp, 5k tach, chrome and powder coating here & there.
Not On Yet: 60#VS
http://s1130.photobucket.com/albums/m53 ... 20Uploads/

Tsbourne09: fuel screw!!!!; Posts: 337; Joined: Sun Aug 14, 2011 8:56 pm

Re: Lifting front end up

by collegekid » Wed Nov 02, 2011 3:53 pm

Installed some moog 7226s springs on mine and absolutely love them, check out my sig for pics

1992 D350 CC LB 5-spd CTD, 366 GSK, Rotated Fuel Pin, Fuel Screw 1 turn off runaway, Factory Match Pyro and Boost, 4" Diamond eye exhaust, and a broken front sway bar :-)

:-)

http://photobucket.com/truckytruck

collegekid: 14mm rotor; Posts: 535; Joined: Fri May 13, 2011 11:15 pm

Re: Lifting front end up

by Tsbourne09 » Mon Nov 14, 2011 6:46 am

http://www.mcbayperformance.com/2WD_FRO ... series.htm

What about these??

93 D250- pump maxed, 3800 spring, hx35, denny T pump top, 7x.015 injectors, timing+, Coolertubz, raptor 150, boost nipple, 4" DP to 6" aussie stacks, built tranny, asa intake, DNR tps, more HP mods, isspro boost, fuel pressure, egt, tranny temp, 5k tach, chrome and powder coating here & there.
Not On Yet: 60#VS
http://s1130.photobucket.com/albums/m53 ... 20Uploads/

Tsbourne09: fuel screw!!!!; Posts: 337; Joined: Sun Aug 14, 2011 8:56 pm

Re: Lifting front end up

by Tsbourne09 » Wed Nov 16, 2011 10:38 pm

Any ideas or comments on them?

93 D250- pump maxed, 3800 spring, hx35, denny T pump top, 7x.015 injectors, timing+, Coolertubz, raptor 150, boost nipple, 4" DP to 6" aussie stacks, built tranny, asa intake, DNR tps, more HP mods, isspro boost, fuel pressure, egt, tranny temp, 5k tach, chrome and powder coating here & there.
Not On Yet: 60#VS
http://s1130.photobucket.com/albums/m53 ... 20Uploads/

Tsbourne09: fuel screw!!!!; Posts: 337; Joined: Sun Aug 14, 2011 8:56 pm

6 posts • Page 1 of 1

Return to Chassis

Jump to:

Who is online

Users browsing this forum: No registered users and 16 guests