Help In need of Spindle

everything but the drivetrain

Moderators: Greenleaf, BC847, Richie O

Help In need of Spindle

Postby jdiesel_us » Fri Jun 05, 2015 4:06 pm

Ok I just took the truck to have the front end aligned and they said the previous owner welded the ls lower ball joint in. I am in need of a ls spindle for a 91 d350. I have talked to all my local junk yards to no avail, checked out ebay, and all the auto parts stores laugh at me. Any Ideas.
jdiesel_us
fuel screw!!!!
 
Posts: 26
Joined: Sat May 03, 2014 12:54 pm

Re: Help In need of Spindle

Postby matthewh » Fri Jun 05, 2015 5:05 pm

You need a spindle or a lower control arm? I've got both, but there from a D250, however I believe there the same.
Lemme do some checking, or maybe somebody will pop in and confirm
'93 W350 5spd Getrag, 4.10 gears, 83k miles and counting, Mods: LPPP AKA Ma Dually
'54 Dodge M37 6.2/700R4/205, 5.89 gears, WC rear axle
matthewh
14mm rotor
 
Posts: 633
Joined: Mon Feb 18, 2013 3:07 am
Location: Boyne City Michigan

Re: Help In need of Spindle

Postby diesel freak01 » Fri Jun 05, 2015 7:36 pm

If they are different I have a 93 d350 for parts. Let me know.
1993 d350 ctd drw 2wd auto
diesel freak01
fuel screw!!!!
 
Posts: 456
Joined: Tue Jul 07, 2009 7:30 am
Location: mcarthur ohio
Top

Re: Help In need of Spindle

Postby thrashingcows » Sat Jun 06, 2015 7:19 pm

If the parts are from a Diesel truck then the D250 and D350 are the same units.
1984/93 Dodge Crewcab, W350, 1 Ton SRW, long box, 330K Km's, M&H spacer, 366 spring, fuel pin to deep side, 14cm housing, Piston LP, PS IC, Isspro Boost, Pyro and tach, NV4500, 29 spline NP205, 3.54's.


Check out the build....http://www.dieseltruckresource.com/dev/ ... 05923.html
thrashingcows
14mm rotor
 
Posts: 575
Joined: Wed Nov 02, 2011 12:00 am
Top

Re: Help In need of Spindle

Postby matthewh » Sat Jun 06, 2015 8:14 pm

Jdiesel pm sent
'93 W350 5spd Getrag, 4.10 gears, 83k miles and counting, Mods: LPPP AKA Ma Dually
'54 Dodge M37 6.2/700R4/205, 5.89 gears, WC rear axle
matthewh
14mm rotor
 
Posts: 633
Joined: Mon Feb 18, 2013 3:07 am
Location: Boyne City Michigan
Top

Re: Help In need of Spindle

Postby BC847 » Sun Jun 07, 2015 5:19 am

As a friendly reminder: ALL Want-Ads and stuff For Sale is to be posted in our Classifieds Section.

Access to the Classifieds section as well as the PM system isn't available until after 25 useful posts have been made. ;)
David

1993 12mm VE Fueled W250 CC, Green
12.67 @ 103.35
Your basic farm truck ;)
BC847
Administrator
 
Posts: 2203
Joined: Wed Jan 03, 2007 5:22 pm
Top

Re: Help In need of Spindle

Postby jdiesel_us » Tue Jun 09, 2015 8:46 am

Thanks to all those who tried to help I got one off Cummins forum.
jdiesel_us
fuel screw!!!!
 
Posts: 26
Joined: Sat May 03, 2014 12:54 pm
Top


Return to Chassis

Who is online

Users browsing this forum: No registered users and 7 guests

cron