Rotor help

everything but the drivetrain

Moderators: Greenleaf, BC847, Richie O

Rotor help

Postby 92cummins89 » Sun Feb 19, 2017 7:06 pm

Replacing rotors pads an calipers but I have a solid 1 in gap between the rotors an thin semi circle dust cover plate
An this isn't righ, the inner brake pad doesn't fit in the groove if this makes any sense
1992 4x4, 4” diamond eye exhaust, nv4500, he351cw
92cummins89
fuel screw!!!!
 
Posts: 165
Joined: Sat Sep 14, 2013 8:46 pm

Re: Rotor help

Postby dazedandconfused » Mon Feb 20, 2017 8:19 am

More details would be great. 2wd or 4wd truck?
1983 Dodge D150 that has been repowered with a 93 Cummins/518 running gear AKA The Ugly Duck! I would much rather build them then buy them.[
User avatar
dazedandconfused
14mm rotor
 
Posts: 6066
Joined: Thu Apr 05, 2007 6:25 pm
Location: Walton, Kentucky

Re: Rotor help

Postby 92cummins89 » Mon Feb 20, 2017 8:40 pm

4x4 it won't let me upload pics
1992 4x4, 4” diamond eye exhaust, nv4500, he351cw
92cummins89
fuel screw!!!!
 
Posts: 165
Joined: Sat Sep 14, 2013 8:46 pm
Top

Re: Rotor help

Postby Rob_O » Wed Feb 22, 2017 10:49 am

Did you change *anything* other than the rotors?
Rob_O
fuel screw!!!!
 
Posts: 77
Joined: Sat Sep 01, 2012 11:03 am
Location: Louisville, KY
Top

Re: Rotor help

Postby DodgeFreak » Wed Feb 22, 2017 2:57 pm

You didn't by chance get 2wd rotors did you??
92 D350 Cab and Chassis. Auto stock, wiring gremlins. 330k miles
92 W250 Ext cab rotted completely out. Auto, pump maxed, 215 ppump nozzles, Denny T2 pin.
85 D350 single wheel, converted to cummins, getrag, turned up 2 turns and afc screw flush.
User avatar
DodgeFreak
14mm rotor
 
Posts: 1701
Joined: Sat May 15, 2010 8:14 pm
Location: Iowa
Top

Re: Rotor help

Postby DodgeFreak » Wed Feb 22, 2017 3:05 pm

Looks like 2wd stick out farther which would be the opposite of your issue I think......is the hub seating all the way on the spindle?? did you change bearings at all??
92 D350 Cab and Chassis. Auto stock, wiring gremlins. 330k miles
92 W250 Ext cab rotted completely out. Auto, pump maxed, 215 ppump nozzles, Denny T2 pin.
85 D350 single wheel, converted to cummins, getrag, turned up 2 turns and afc screw flush.
User avatar
DodgeFreak
14mm rotor
 
Posts: 1701
Joined: Sat May 15, 2010 8:14 pm
Location: Iowa
Top

Re: Rotor help

Postby 92cummins89 » Sat Feb 03, 2018 1:42 pm

still having this issue everything is seated right an both sides have the same gap

when the inner pad is in the grooves there is a big gap b4 it meets up with the rotor

i feel as if the rotor isnt deep enough if that makes sense
1992 4x4, 4” diamond eye exhaust, nv4500, he351cw
92cummins89
fuel screw!!!!
 
Posts: 165
Joined: Sat Sep 14, 2013 8:46 pm
Top

Re: Rotor help

Postby thrashingcows » Mon Feb 05, 2018 5:44 pm

Pics would definitely help us visualize what is going on and help you figure this out. I know when I did the front end on my W350 I bought the wrong 8 bolt rotors....they were for a 4wd, but were for the rare 8 bolt D44 front axle, not the 4500# D60. Maybe that is the problem?
1984/93 Dodge Crewcab, W350, 1 Ton SRW, long box, 330K Km's, M&H spacer, 366 spring, fuel pin to deep side, 14cm housing, Piston LP, PS IC, Isspro Boost, Pyro and tach, NV4500, 29 spline NP205, 3.54's.


Check out the build....http://www.dieseltruckresource.com/dev/ ... 05923.html
thrashingcows
14mm rotor
 
Posts: 557
Joined: Wed Nov 02, 2011 12:00 am
Top

Re: Rotor help

Postby 92cummins89 » Tue Feb 06, 2018 12:39 pm

well i figured it out when i did my passenger side a few months ago i had to replace the axle u joint and when i went back together with it i mixed up the shaft and the piece that holds the caliper and had them swaped witch is where i was getting my gap from dumb ass moment for me
1992 4x4, 4” diamond eye exhaust, nv4500, he351cw
92cummins89
fuel screw!!!!
 
Posts: 165
Joined: Sat Sep 14, 2013 8:46 pm
Top


Return to Chassis

Who is online

Users browsing this forum: No registered users and 1 guest