Double Cardan CV Joint, Front axel

Moderators: Greenleaf, BC847, Richie O

Double Cardan CV Joint, Front axel

Postby BradPA » Tue Mar 05, 2019 10:08 am

I broke my Stock Double Cardan CV joint.. both Flange and H part. shaft with ball on end may work if i have to rebuild.. cup where ball fits against shaft was tore up..
So i looked up a new one ...
I have the dana 60 , 4500 front axle ..205 transfer case, 5 speed manual trans
OOboy A1 Cardone part number 659327 looks to be what i want... but these are not in stock or available right now.
So any ideas .. or where I can find a rebuild able one..
My truck Thanks you in advance.... :D
Brad
1991.5 - Dodge W250
BradPA
fuel pin?
 
Posts: 6
Joined: Tue Mar 05, 2019 9:30 am

Re: Double Cardan CV Joint, Front axel

Postby thrashingcows » Tue Mar 05, 2019 7:34 pm

Take a look at car-part.com, they link 1000's of junkyards and wreckers.
1984/93 Dodge Crewcab, W350, 1 Ton SRW, long box, 330K Km's, M&H spacer, 366 spring, fuel pin to deep side, 14cm housing, Piston LP, PS IC, Isspro Boost, Pyro and tach, NV4500, 29 spline NP205, 3.54's.


Check out the build....http://www.dieseltruckresource.com/dev/ ... 05923.html
thrashingcows
14mm rotor
 
Posts: 575
Joined: Wed Nov 02, 2011 12:00 am

Re: Double Cardan CV Joint, Front axel

Postby BradPA » Wed Mar 06, 2019 5:51 am

thanks ..
i checked them out and many others
car-parts list 2 complete axles for a Dana 44 .. they also list the flange and H part..

I think the length is the key, with a 5 speed, D 60 and 4500 front end and a 205 transfer is (24 3/4)
if i buy parts plus u joints and try to rebuild using my axle shaft with tore up cup .. sounds like a waste of time .. and may not work ..
on the axle shaft there's a tin cup tack welded on end this is where the ball seats. this is tore up and ball may not seat right or hold grease.. So the last week i have been doing searches and info

the Cardon 659327, looks to be correct replacement i need .. and from what i see they may make a run of them sometime this summer.. i have to wait and see

Hey Thanks again...
BradPA
fuel pin?
 
Posts: 6
Joined: Tue Mar 05, 2019 9:30 am
Top

Re: Double Cardan CV Joint, Front axel

Postby thrashingcows » Wed Mar 06, 2019 2:27 pm

IS there any reason you can not take your broken drive shaft down to a driveline specialty shop locally and have them build you a new one?
1984/93 Dodge Crewcab, W350, 1 Ton SRW, long box, 330K Km's, M&H spacer, 366 spring, fuel pin to deep side, 14cm housing, Piston LP, PS IC, Isspro Boost, Pyro and tach, NV4500, 29 spline NP205, 3.54's.


Check out the build....http://www.dieseltruckresource.com/dev/ ... 05923.html
thrashingcows
14mm rotor
 
Posts: 575
Joined: Wed Nov 02, 2011 12:00 am
Top

Re: Double Cardan CV Joint, Front axel

Postby BradPA » Wed Mar 06, 2019 4:05 pm

Hey good News.. they are or will be making some soon expected ship date middle of next month..
so i ordered one,,, thanks again...

its total cost,, i would still need H and flange ,, u joints...and CV its self then fix the shaft..
i just have to remember that there are 3 grease fittings that need my attention. not 2 :D
BradPA
fuel pin?
 
Posts: 6
Joined: Tue Mar 05, 2019 9:30 am
Top


Return to Part numbers (old,new,cross reference)

Who is online

Users browsing this forum: No registered users and 7 guests