74 W300 gasser pulling vid

Sled-pulling, Drag results, Dyno results

Moderators: Greenleaf, KTA, BC847, Richie O

74 W300 gasser pulling vid

Postby bgilbert » Fri Jul 23, 2010 2:15 pm

Here's my first ever hook, for the truck and myself: http://www.youtube.com/watch?v=kPGHCobt3cM

It's a 74 Dodge W300 cab and chassis dually truck that I put a single wheel pickup bed on. It's got a 135" wheel base, 4" longer than a pickup. 360, holley 4 barrel, 4 speed and stock clutch, 4.88 gears, dana 70's front and rear. I think the rings might be bad, as you can see it had a nice oil smoke plume out the back. It also blew the dipstick out and a little bit of oil under the hood and on the intake. I also let out of it at the end, I think it might have had another foot or so haha. I looked out my mirrors as the truck was slowing down and seen all the white smoke. I thought it was the bed coming down on my tires, I figured well they're on fire I better let out :lol: . At the end of the video you can see how far back the rear axle sits from the longer wheel base. I had fun and will do it again.
Bill Gilbert
85 D350 crew with 90 6BT intercooled Getrag 3.07's
93 D350 single cab Getrag 3.54's.
bgilbert
14mm rotor
 
Posts: 2253
Joined: Wed Jan 03, 2007 5:04 pm
Location: Terre Haute, Indiana

Re: 74 W300 gasser pulling vid

Postby pulltilbroke » Fri Jul 23, 2010 6:23 pm

Not bad at all for your first hook!!!
90 W250 reg cab, Modified knuder valve, reversed reciprocting dinglearm adjusted, High volume flux capacitor,upgraded whirlygig, A clutch and a hitch
93 W350 ext cab dually, getrag and a few adjustments
pulltilbroke
14mm rotor
 
Posts: 1410
Joined: Fri Jan 18, 2008 1:20 am
Location: Eagle Ne

Re: 74 W300 gasser pulling vid

Postby JBradley500 » Sat Jul 24, 2010 3:44 am

man i wish i would have went to paris. jobs really get in the way of having a good time.
92 W250- K&N Filter, Smoke Screw Adjusted, Synthetic Transmission Fluid.
340hp/662tq (8/24/12)
User avatar
JBradley500
fuel screw!!!!
 
Posts: 255
Joined: Sun Aug 23, 2009 5:52 am
Top

Re: 74 W300 gasser pulling vid

Postby GO OVRIT » Sat Jul 24, 2010 11:35 am

I wish I had a video of my 74 w300 440 truck hooked to the sled. It would be a good laugh. I think you could've hook yours to my truck and the sled an still pulled farther. The engine I'm putting together now should do a little better.
92 W250 ext cab 518, big sticks, a-1000, PDR HX40, 4" exhaust w/aeroturbine, pump tweaked, K&N filter Tims Cooler tubes and 3" i/c, gauges
GO OVRIT
14mm rotor
 
Posts: 554
Joined: Tue Nov 13, 2007 8:59 pm
Location: Gloucester Va.
Top

Re: 74 W300 gasser pulling vid

Postby bgilbert » Sat Jul 24, 2010 4:36 pm

Thanks guys. Your 440 truck didn't pull it out the gate? :lol: Are you building a Mopar engine? After seeing a 396 Chevy in a 74 W200 and then everybody and their brother around here telling me how easier and cheaper it would be to build a big block Chevy, it's got me thinking..
Bill Gilbert
85 D350 crew with 90 6BT intercooled Getrag 3.07's
93 D350 single cab Getrag 3.54's.
bgilbert
14mm rotor
 
Posts: 2253
Joined: Wed Jan 03, 2007 5:04 pm
Location: Terre Haute, Indiana
Top

Re: 74 W300 gasser pulling vid

Postby pulltilbroke » Sat Jul 24, 2010 7:40 pm

Don't put a Cheby motor in there, I'm a Chevy guy but thats just sacreligous putting a Chevy in a Mopar.
90 W250 reg cab, Modified knuder valve, reversed reciprocting dinglearm adjusted, High volume flux capacitor,upgraded whirlygig, A clutch and a hitch
93 W350 ext cab dually, getrag and a few adjustments
pulltilbroke
14mm rotor
 
Posts: 1410
Joined: Fri Jan 18, 2008 1:20 am
Location: Eagle Ne
Top

Re: 74 W300 gasser pulling vid

Postby 1STGENFARMBOY » Sun Jul 25, 2010 5:21 am

What is all this talk of gas motors??? $1000 you could have a ( D I E S E L )
93 W250 STD CAB, AUTO 3.55, GAUGES, 80HP DDP STICKS, DENNY T ,16CM HOUSING, 60MM GILLETT, VE MAXED,BHAF, BHFF, 366 SPRING,P/S INTERCOOLER, TIMS COOLER TUBS, TIMMING 1/8 BUMP,4in TURBO BACK TO DUEL 5IN STACKS,33 12.50 BFG, HOLLEY BLACK, CONVERTER COOMING.
User avatar
1STGENFARMBOY
14mm rotor
 
Posts: 2081
Joined: Mon Sep 28, 2009 2:23 pm
Location: PITTSBURG ILL
Top

Re: 74 W300 gasser pulling vid

Postby Richie O » Mon Jul 26, 2010 3:08 pm

I like the gasser pulls just as much. I like it. :D A guy up here has a 71 chevy that is just for pulling. He reved it up so high and dumped the clutch that the headlight popped out and was hanging by the wires. :lol: I keep wanting to do a gasser truck just for play. Add it to the " want " list.
1989 W250 727, 3.07 L/S, S300, P/S Intercooler, Stans exaust, Pump adjustments, 127k miles,297 hp
1993 W250 extended cab, rag, 4.10 l/s, 6x16's, HTT 62/71/14 piston l/p, Isspro EV series tach, fuel pressure, boost, oil pres, water temp, volt, pryo, 132k/ 301 hp
1992 W250 with NV4500, 3.54's, 16cm 60mm GDS H1C, ground stock cone, Isspro tach, pryo, boost, fuel pressure, slow, rusty, dented,180k
User avatar
Richie O
Administrator
 
Posts: 4126
Joined: Sat May 17, 2008 9:01 pm
Location: New England
Top

Re: 74 W300 gasser pulling vid

Postby bgilbert » Sat Jul 31, 2010 12:00 am

Second pull for the truck and driver. Did a little better this time. 290 something feet. Didn't catch the standings but Nicole said there were at least four trucks that didn't go as far as I did 8) . http://www.youtube.com/watch?v=T7J9ONiOZPA
Bill Gilbert
85 D350 crew with 90 6BT intercooled Getrag 3.07's
93 D350 single cab Getrag 3.54's.
bgilbert
14mm rotor
 
Posts: 2253
Joined: Wed Jan 03, 2007 5:04 pm
Location: Terre Haute, Indiana
Top

Re: 74 W300 gasser pulling vid

Postby bgilbert » Sat Jul 31, 2010 12:12 am

Here's a twin to my truck, as far as the engine, trans, t-case, axles and gearing: http://www.youtube.com/watch?v=8nUawbsaSv4 .
It's another 74 W300 cab and chassis truck. 2 barrel carb though :oops: . Evidently his clutch won't hold 2nd gear low range, so he pulls in 1st gear low range.
bgilbert
14mm rotor
 
Posts: 2253
Joined: Wed Jan 03, 2007 5:04 pm
Location: Terre Haute, Indiana
Top

Re: 74 W300 gasser pulling vid

Postby KTA » Fri Aug 06, 2010 6:47 pm

I did some pulling last week too. Its a 466cid 3000 rpm hot farm Deere. It spins out road gear in the 10000lb class, this was the 13000lb hook. The injection pump developed a governor problem that hook(pieces came loose) and made it want to hunt and that started it bouncing some. Still managed the win by 8foot on a very competitive class. :D
The video
http://www.youtube.com/watch?v=zDHSzj7fJcI
Fleet of Junk: 1989 D350 627rwhp 1300 tq B-1/Hx60 twins, KTA pump/injectors, ported head, BIG fuel supply. 13.75@ 109.5mph 1/4: 1992 W350 Cab-chasis, 1993 W350 ext cab cust.370 inj Hx40/16cm 290rwhp hydroboost brakes,1984 D350 crew-cab another project.
User avatar
KTA
diesel guru/mod
 
Posts: 1846
Joined: Thu Jan 04, 2007 2:23 pm
Location: Shelby County, Ky
Top

Re: 74 W300 gasser pulling vid

Postby Richie O » Fri Aug 06, 2010 7:28 pm

That thing had some ground speed. :shock:
1989 W250 727, 3.07 L/S, S300, P/S Intercooler, Stans exaust, Pump adjustments, 127k miles,297 hp
1993 W250 extended cab, rag, 4.10 l/s, 6x16's, HTT 62/71/14 piston l/p, Isspro EV series tach, fuel pressure, boost, oil pres, water temp, volt, pryo, 132k/ 301 hp
1992 W250 with NV4500, 3.54's, 16cm 60mm GDS H1C, ground stock cone, Isspro tach, pryo, boost, fuel pressure, slow, rusty, dented,180k
User avatar
Richie O
Administrator
 
Posts: 4126
Joined: Sat May 17, 2008 9:01 pm
Location: New England
Top

Re: 74 W300 gasser pulling vid

Postby KTA » Fri Aug 06, 2010 7:57 pm

Wheel speed is right at 25mph.
Fleet of Junk: 1989 D350 627rwhp 1300 tq B-1/Hx60 twins, KTA pump/injectors, ported head, BIG fuel supply. 13.75@ 109.5mph 1/4: 1992 W350 Cab-chasis, 1993 W350 ext cab cust.370 inj Hx40/16cm 290rwhp hydroboost brakes,1984 D350 crew-cab another project.
User avatar
KTA
diesel guru/mod
 
Posts: 1846
Joined: Thu Jan 04, 2007 2:23 pm
Location: Shelby County, Ky
Top

Re: 74 W300 gasser pulling vid

Postby bgilbert » Sat Aug 07, 2010 7:14 am

That looked awesome Brian. Now everyone sees what you've been doing while waiting for someone to knock you off your high hp chair :lol: !
bgilbert
14mm rotor
 
Posts: 2253
Joined: Wed Jan 03, 2007 5:04 pm
Location: Terre Haute, Indiana
Top

Re: 74 W300 gasser pulling vid

Postby KTA » Sun Aug 08, 2010 9:06 am

Thats funny Bill. I think this tractor is only about 1/1000th of the diesel related projects I have going on. I hooked it again last night and won by 20feet. :D Its kind of fun going 300+feet without the front wheels ever touching the ground. Sorry there are no videos though that I am aware of. I think a max wedge 440 with 2 650 holley 4bbls should wake that rig of yours up. :grin:
Fleet of Junk: 1989 D350 627rwhp 1300 tq B-1/Hx60 twins, KTA pump/injectors, ported head, BIG fuel supply. 13.75@ 109.5mph 1/4: 1992 W350 Cab-chasis, 1993 W350 ext cab cust.370 inj Hx40/16cm 290rwhp hydroboost brakes,1984 D350 crew-cab another project.
User avatar
KTA
diesel guru/mod
 
Posts: 1846
Joined: Thu Jan 04, 2007 2:23 pm
Location: Shelby County, Ky
Top

Next

Return to Competition

Who is online

Users browsing this forum: No registered users and 2 guests