Updated dyno results and video of the 93

Sled-pulling, Drag results, Dyno results

Moderators: Greenleaf, KTA, BC847, Richie O

Updated dyno results and video of the 93

Postby Richie O » Sat Oct 23, 2010 5:15 pm

Ran the 93 again today with the very same tune as before. My power went down 12 horses but I did change from a 32 inch tire to just under a 35. I was at 289 today, down from 301 with the small tires.


http://www.youtube.com/watch?v=TtBWuHMwWLA



.
1989 W250 727, 3.07 L/S, S300, P/S Intercooler, Stans exaust, Pump adjustments, 127k miles,297 hp
1993 W250 extended cab, rag, 4.10 l/s, 6x16's, HTT 62/71/14 piston l/p, Isspro EV series tach, fuel pressure, boost, oil pres, water temp, volt, pryo, 132k/ 301 hp
1992 W250 with NV4500, 3.54's, 16cm 60mm GDS H1C, ground stock cone, Isspro tach, pryo, boost, fuel pressure, slow, rusty, dented,180k
User avatar
Richie O
Administrator
 
Posts: 4171
Joined: Sat May 17, 2008 9:01 pm
Location: New England

Re: Updated dyno results and video of the 93

Postby 1STGENFARMBOY » Sat Oct 23, 2010 5:26 pm

Looked like a good day, spend every minute with you kids you can they are at a fun age right now, when my boy was Jays age we were
inseperable :? , now he thinks i'm stupid cause i don't like drinkin beer, and i rarely see him, he is 23 now, but we (did) have fun.

Dar
93 W250 STD CAB, AUTO 3.55, GAUGES, 80HP DDP STICKS, DENNY T ,16CM HOUSING, 60MM GILLETT, VE MAXED,BHAF, BHFF, 366 SPRING,P/S INTERCOOLER, TIMS COOLER TUBS, TIMMING 1/8 BUMP,4in TURBO BACK TO DUEL 5IN STACKS,33 12.50 BFG, HOLLEY BLACK, CONVERTER COOMING.
User avatar
1STGENFARMBOY
14mm rotor
 
Posts: 2089
Joined: Mon Sep 28, 2009 2:23 pm
Location: PITTSBURG ILL

Re: Updated dyno results and video of the 93

Postby Richie O » Sat Oct 23, 2010 5:30 pm

I almost had Stacey bring up the 89 with Hope, but they ended up doing the mom/daughter thing ( shopping ). We had a good time. ( and I don't drink either ) ;)
1989 W250 727, 3.07 L/S, S300, P/S Intercooler, Stans exaust, Pump adjustments, 127k miles,297 hp
1993 W250 extended cab, rag, 4.10 l/s, 6x16's, HTT 62/71/14 piston l/p, Isspro EV series tach, fuel pressure, boost, oil pres, water temp, volt, pryo, 132k/ 301 hp
1992 W250 with NV4500, 3.54's, 16cm 60mm GDS H1C, ground stock cone, Isspro tach, pryo, boost, fuel pressure, slow, rusty, dented,180k
User avatar
Richie O
Administrator
 
Posts: 4171
Joined: Sat May 17, 2008 9:01 pm
Location: New England
Top

Re: Updated dyno results and video of the 93

Postby PJ 3 » Sat Oct 23, 2010 5:41 pm

That's true......it was today ! Wish I could have made it down. It looks as though there was a good turn out. Any other 1 st gens there ?
Pete

1992 W250
User avatar
PJ 3
fuel screw!!!!
 
Posts: 220
Joined: Mon May 18, 2009 4:38 pm
Location: New Brunswick, Canada
Top

Re: Updated dyno results and video of the 93

Postby Richie O » Sat Oct 23, 2010 5:47 pm

PJ 3 wrote:That's true......it was today ! Wish I could have made it down. It looks as though there was a good turn out. Any other 1 st gens there ?


I was the only first gen there this year. The guy that filmed for me ( Taterfarm ) is in the middle of rebuilding his truck after getting t boned a couple of winters back ( slow project ) DZLDAMON shipped out a couple days ago for the orient, and Bradshaw106 is tearing his down due to rust. :?
1989 W250 727, 3.07 L/S, S300, P/S Intercooler, Stans exaust, Pump adjustments, 127k miles,297 hp
1993 W250 extended cab, rag, 4.10 l/s, 6x16's, HTT 62/71/14 piston l/p, Isspro EV series tach, fuel pressure, boost, oil pres, water temp, volt, pryo, 132k/ 301 hp
1992 W250 with NV4500, 3.54's, 16cm 60mm GDS H1C, ground stock cone, Isspro tach, pryo, boost, fuel pressure, slow, rusty, dented,180k
User avatar
Richie O
Administrator
 
Posts: 4171
Joined: Sat May 17, 2008 9:01 pm
Location: New England
Top

Re: Updated dyno results and video of the 93

Postby ellis93 » Sat Oct 23, 2010 7:09 pm

Man lookin at ur truck sportin those stack makes me want to put some on my red&silver beast. Gotta say that thing looks really good rolling with those wheels on it too.
93 D250 ,5 speed,4.11s,k&n autometer tach pyro trans boost guages,GDS 60mm h1c 14cm,honed 5x10,hplp/reg,1/8 timing,M+H M2 fuel pin, tims cooler tubz
User avatar
ellis93
14mm rotor
 
Posts: 7761
Joined: Wed Feb 17, 2010 3:16 pm
Location: lucedale,mississippi
Top

Re: Updated dyno results and video of the 93

Postby The_Head » Sat Oct 23, 2010 8:18 pm

Please tell me the purpose of making this thread. I are confused.
1992 Dodge Power Ram 250 (sold)
2014 Dodge Ram 2500 Tradesman, RC, 4WD, G56, Traxda 2.5/1" leveling kit
User avatar
The_Head
14mm rotor
 
Posts: 791
Joined: Sun Dec 06, 2009 9:04 am
Location: WyO
Top

Re: Updated dyno results and video of the 93

Postby Richie O » Sat Oct 23, 2010 8:21 pm

The_Head wrote:Please tell me the purpose of making this thread. I are confused.


Lets see.

1. Its in the competition area ( dyno, sled pulling, drag times )
2. Thats the only point needed.
1989 W250 727, 3.07 L/S, S300, P/S Intercooler, Stans exaust, Pump adjustments, 127k miles,297 hp
1993 W250 extended cab, rag, 4.10 l/s, 6x16's, HTT 62/71/14 piston l/p, Isspro EV series tach, fuel pressure, boost, oil pres, water temp, volt, pryo, 132k/ 301 hp
1992 W250 with NV4500, 3.54's, 16cm 60mm GDS H1C, ground stock cone, Isspro tach, pryo, boost, fuel pressure, slow, rusty, dented,180k
User avatar
Richie O
Administrator
 
Posts: 4171
Joined: Sat May 17, 2008 9:01 pm
Location: New England
Top

Re: Updated dyno results and video of the 93

Postby ellis93 » Sat Oct 23, 2010 8:27 pm

I thought it was OK.
93 D250 ,5 speed,4.11s,k&n autometer tach pyro trans boost guages,GDS 60mm h1c 14cm,honed 5x10,hplp/reg,1/8 timing,M+H M2 fuel pin, tims cooler tubz
User avatar
ellis93
14mm rotor
 
Posts: 7761
Joined: Wed Feb 17, 2010 3:16 pm
Location: lucedale,mississippi
Top

Re: Updated dyno results and video of the 93

Postby 1STGENFARMBOY » Sat Oct 23, 2010 8:38 pm

John's just upset cause you don't have any documentation on paper, or notorized publication of your
run. :lol: :lol: :lol: sorry John i couldn't help myself.

Darwin
93 W250 STD CAB, AUTO 3.55, GAUGES, 80HP DDP STICKS, DENNY T ,16CM HOUSING, 60MM GILLETT, VE MAXED,BHAF, BHFF, 366 SPRING,P/S INTERCOOLER, TIMS COOLER TUBS, TIMMING 1/8 BUMP,4in TURBO BACK TO DUEL 5IN STACKS,33 12.50 BFG, HOLLEY BLACK, CONVERTER COOMING.
User avatar
1STGENFARMBOY
14mm rotor
 
Posts: 2089
Joined: Mon Sep 28, 2009 2:23 pm
Location: PITTSBURG ILL
Top

Re: Updated dyno results and video of the 93

Postby Richie O » Sat Oct 23, 2010 8:46 pm

Image




.
1989 W250 727, 3.07 L/S, S300, P/S Intercooler, Stans exaust, Pump adjustments, 127k miles,297 hp
1993 W250 extended cab, rag, 4.10 l/s, 6x16's, HTT 62/71/14 piston l/p, Isspro EV series tach, fuel pressure, boost, oil pres, water temp, volt, pryo, 132k/ 301 hp
1992 W250 with NV4500, 3.54's, 16cm 60mm GDS H1C, ground stock cone, Isspro tach, pryo, boost, fuel pressure, slow, rusty, dented,180k
User avatar
Richie O
Administrator
 
Posts: 4171
Joined: Sat May 17, 2008 9:01 pm
Location: New England
Top

Re: Updated dyno results and video of the 93

Postby 1STGENFARMBOY » Sat Oct 23, 2010 8:56 pm

There ya go John, ask and ye shall recieve.

Dar
93 W250 STD CAB, AUTO 3.55, GAUGES, 80HP DDP STICKS, DENNY T ,16CM HOUSING, 60MM GILLETT, VE MAXED,BHAF, BHFF, 366 SPRING,P/S INTERCOOLER, TIMS COOLER TUBS, TIMMING 1/8 BUMP,4in TURBO BACK TO DUEL 5IN STACKS,33 12.50 BFG, HOLLEY BLACK, CONVERTER COOMING.
User avatar
1STGENFARMBOY
14mm rotor
 
Posts: 2089
Joined: Mon Sep 28, 2009 2:23 pm
Location: PITTSBURG ILL
Top

Re: Updated dyno results and video of the 93

Postby The_Head » Sat Oct 23, 2010 9:39 pm

Yeah, but you lost 11 horsepower, so I don't see the point? What is the information you are trying to pass on to us?
1992 Dodge Power Ram 250 (sold)
2014 Dodge Ram 2500 Tradesman, RC, 4WD, G56, Traxda 2.5/1" leveling kit
User avatar
The_Head
14mm rotor
 
Posts: 791
Joined: Sun Dec 06, 2009 9:04 am
Location: WyO
Top

Re: Updated dyno results and video of the 93

Postby 1STGENFARMBOY » Sun Oct 24, 2010 5:26 am

He was trying to show that even though the new weels and tires look great they robbed 12 hp
from his truck....so be ware of new wheels and tires. :D he looked for a lost hp thread but
couldn't find one. :lol: :lol: John you must have had a bad day yesterday, lets hope that
today is better.

Dar
93 W250 STD CAB, AUTO 3.55, GAUGES, 80HP DDP STICKS, DENNY T ,16CM HOUSING, 60MM GILLETT, VE MAXED,BHAF, BHFF, 366 SPRING,P/S INTERCOOLER, TIMS COOLER TUBS, TIMMING 1/8 BUMP,4in TURBO BACK TO DUEL 5IN STACKS,33 12.50 BFG, HOLLEY BLACK, CONVERTER COOMING.
User avatar
1STGENFARMBOY
14mm rotor
 
Posts: 2089
Joined: Mon Sep 28, 2009 2:23 pm
Location: PITTSBURG ILL
Top

Re: Updated dyno results and video of the 93

Postby bgilbert » Sun Oct 24, 2010 7:18 am

The_Head wrote:Please tell me the purpose of making this thread. I are confused.

Hmm it's in the Competition forum, where you post "Sled-pulling, Drag results, Dyno results". Are you confused with what website you're on?
Bill Gilbert
85 D350 crew with 90 6BT intercooled Getrag 3.07's
93 D350 single cab Getrag 3.54's.
bgilbert
14mm rotor
 
Posts: 2253
Joined: Wed Jan 03, 2007 5:04 pm
Location: Terre Haute, Indiana
Top

Next

Return to Competition

Who is online

Users browsing this forum: No registered users and 15 guests