dyno numbers

Sled-pulling, Drag results, Dyno results

Moderators: Greenleaf, KTA, BC847, Richie O

Postby JD730 » Sun May 18, 2008 9:01 pm

New numbers:
424/1039
Mildly setup 14mm H/R, 6x16's, 62/65/12, 47RH, etc....
Mike
Thats not a leak, its the external lubrication system.
The "Rattle Box"
93 W250 Silver Club Cab, few tweaks here and there.
John Deere Two Cylinders, too many to list.
JD730
fuel screw!!!!
 
Posts: 131
Joined: Tue Feb 06, 2007 10:27 am
Location: Belvidere, NJ

Postby TWorline » Mon Jun 02, 2008 7:21 pm

New number :roll: they could not do TQ. 348 HP on a Dyno Jet 248 I will post a picture of the sheet later this week.
Tim Worline
1992 W250 Club Cab LE, S300 62/71, 5" stainless intake, 4" into 5" exhaust, ATS exhaust manifold, SDX 5X18 Injectors, AirDog 150, Borgeson shaft, Coolingmist Vari-cool, Con OFEK, 3" Stainless CoolerTubz, 354/749.

http://www.CoolerTubz.com/
User avatar
TWorline
14mm rotor
 
Posts: 2480
Joined: Thu Jan 04, 2007 6:32 pm
Location: Continental, Oh.

Postby SNOOT » Mon Jun 02, 2008 7:28 pm

I just did 270/680 on my truck. Stock pump settings with only a GOV spring and old smokey fuel pin. PDR-35 and DDP 4 injectors.

Ran the dyno in 3rd gear pretty sure it would have been more if I could have run O/D.

I am very sure this trans will hold 450HP no problem never had one so strong.

The tranny is working great now I will just add fuel and more air.

How do you like them shifts now.. This is a non-lock up trans.

http://www.youtube.com/watch?v=4TF3NzJb6fo
1993 W350
User avatar
SNOOT
14mm rotor
 
Posts: 609
Joined: Tue Mar 11, 2008 8:05 pm
Location: Seattle, WA.
Top

Postby Falcon » Tue Jun 03, 2008 11:27 am

Did mine the same date as Snoot.
Got a 253 and 541tq also ran in third gear. Snoot did you get any pictures of mine on the dyno?
Greg
Graham, Washington
"FIRST REAL TRUCK ENGINE...
LAST REAL TRUCK!!!
93 ex cab 4x4, Hybred 35/40,4" exaust all the way,pump turned alittle,DDP Stage III's, 366 spring,DDP fuel pin,AFE first gen air intake,pyro and boost gauges
Falcon
fuel screw!!!!
 
Posts: 125
Joined: Wed Jan 03, 2007 8:41 am
Top

Postby PToombs » Tue Jun 03, 2008 3:46 pm

Tim, isn't that about where you were before? Or a little lower?
I was looking at the truck last nite, found I wasn't getting full throttle! :shock: Turns out the spring return bellcrank thingy where the cable transitions to the linkage has a stop on it. Well, it did last nite. It doesn't now. ;) :wrench:
pete

Just enough power to break everything behind the crankshaft.
User avatar
PToombs
14mm rotor
 
Posts: 11367
Joined: Sun Jan 07, 2007 6:13 pm
Location: Syracuse NY. Snow central!
Top

Postby TWorline » Tue Jun 03, 2008 4:55 pm

I was at 295/690 last year at the Sheids event. Didn`t I mention that it would be a good ideal to check your throttle travel at SOP last year? ;-)
Tim Worline
1992 W250 Club Cab LE, S300 62/71, 5" stainless intake, 4" into 5" exhaust, ATS exhaust manifold, SDX 5X18 Injectors, AirDog 150, Borgeson shaft, Coolingmist Vari-cool, Con OFEK, 3" Stainless CoolerTubz, 354/749.

http://www.CoolerTubz.com/
User avatar
TWorline
14mm rotor
 
Posts: 2480
Joined: Thu Jan 04, 2007 6:32 pm
Location: Continental, Oh.
Top

Postby SNOOT » Tue Jun 03, 2008 6:33 pm

Falcon wrote:Did mine the same date as Snoot.
Got a 253 and 541tq also ran in third gear. Snoot did you get any pictures of mine on the dyno?


I think I have video I will upload and post tonight here... Are you sure you want to here the difference in shifting from my truck to yours?

Had lots of fun ... Will post Lennys burn out also.
1993 W350
User avatar
SNOOT
14mm rotor
 
Posts: 609
Joined: Tue Mar 11, 2008 8:05 pm
Location: Seattle, WA.
Top

Postby TWorline » Tue Jun 03, 2008 7:52 pm

Here is a picture of my graph. 8)

[img][img]http://i116.photobucket.com/albums/o28/DieselRam250/S5009382.jpg[/img]

Here is a link to the video of the first run which shows 130 mph on the graph. The HP reallly does drop off after about 3200 RPM. I think the operater ran it out to 3600 RPM on that run.
http://s116.photobucket.com/albums/o28/DieselRam250/W250%20Videos/?action=view&current=S5009371.flv
Tim Worline
1992 W250 Club Cab LE, S300 62/71, 5" stainless intake, 4" into 5" exhaust, ATS exhaust manifold, SDX 5X18 Injectors, AirDog 150, Borgeson shaft, Coolingmist Vari-cool, Con OFEK, 3" Stainless CoolerTubz, 354/749.

http://www.CoolerTubz.com/
User avatar
TWorline
14mm rotor
 
Posts: 2480
Joined: Thu Jan 04, 2007 6:32 pm
Location: Continental, Oh.
Top

Postby SNOOT » Tue Jun 03, 2008 9:20 pm

Greg
Sorry this is all I got of you..

http://www.youtube.com/watch?v=DRNaAvaCeS4
1993 W350
User avatar
SNOOT
14mm rotor
 
Posts: 609
Joined: Tue Mar 11, 2008 8:05 pm
Location: Seattle, WA.
Top

Postby Falcon » Wed Jun 04, 2008 8:01 am

Thanks can ya sendt it to me?
Greg
Graham, Washington
"FIRST REAL TRUCK ENGINE...
LAST REAL TRUCK!!!
93 ex cab 4x4, Hybred 35/40,4" exaust all the way,pump turned alittle,DDP Stage III's, 366 spring,DDP fuel pin,AFE first gen air intake,pyro and boost gauges
Falcon
fuel screw!!!!
 
Posts: 125
Joined: Wed Jan 03, 2007 8:41 am
Top

Postby PToombs » Wed Jun 04, 2008 6:04 pm

Tim, I noticed last nite my throttle lacked 3/16 from the end. Turns out the cable/linkage bellcrank thingy has stops on it! I fixed that. What do you think, 25-30 hp?
pete

Just enough power to break everything behind the crankshaft.
User avatar
PToombs
14mm rotor
 
Posts: 11367
Joined: Sun Jan 07, 2007 6:13 pm
Location: Syracuse NY. Snow central!
Top

Postby TWorline » Wed Jun 04, 2008 6:13 pm

PToombs wrote:Tim, I noticed last nite my throttle lacked 3/16 from the end. Turns out the cable/linkage bellcrank thingy has stops on it! I fixed that. What do you think, 25-30 hp?


Oh yeah!!! ;)
Tim Worline
1992 W250 Club Cab LE, S300 62/71, 5" stainless intake, 4" into 5" exhaust, ATS exhaust manifold, SDX 5X18 Injectors, AirDog 150, Borgeson shaft, Coolingmist Vari-cool, Con OFEK, 3" Stainless CoolerTubz, 354/749.

http://www.CoolerTubz.com/
User avatar
TWorline
14mm rotor
 
Posts: 2480
Joined: Thu Jan 04, 2007 6:32 pm
Location: Continental, Oh.
Top

Postby bgilbert » Sat Jun 14, 2008 4:36 pm

Dynoed the sloppy auto 91.5 truck. Did 338hp and 813ftlbs. I'm not sure if the rpm calculated was correct (no crank rpm sensor), the graph only shows running it out to 3100rpm. It sure sounded like at least 3500rpm. We couldn't get it to stay in OD, it kept kicking down, even at 100mph :shock: :evil: . So all runs were in 3rd gear direct 1:1. Sure sounded good! I think this goes to show CK that he ain't makin no mid 400's with a stock auto and nonIC'd. 58psi out of a large (somewhat) single Pro52 that spools right now. :lol: The same injectors and turbo with an air to water aftercooler, basically nonIC'd in my 89 5 speed truck made 443hp and 900ish ftlbs. Damn auto steals alot! I'm surprised with the torque number though out of an auto. Dynomite dynojet 1400lb roller.
Bill Gilbert
85 D350 crew with 90 6BT intercooled Getrag 3.07's
93 D350 single cab Getrag 3.54's.
bgilbert
14mm rotor
 
Posts: 2253
Joined: Wed Jan 03, 2007 5:04 pm
Location: Terre Haute, Indiana
Top

Postby Cschafer » Sat Jun 14, 2008 8:03 pm

new numbers 6-14-08
356/753 fuel
487/1005 nitrous

6x.018, silver bullit,366 spring, a-1000 supply, no afc

Image
90 W250,bank$ intercooled,I.I. Silver Bulit, 38mm ex. gate, a-1000 supply, 6x.018's, MIA AFC lever, 366 spring, 2 stages of laughing gas, 486/1005 on the gas. sold
91 w250 wrecker
User avatar
Cschafer
fuel screw!!!!
 
Posts: 197
Joined: Tue Jan 09, 2007 6:36 pm
Location: Mt.Pleasant MI
Top

Postby oldcool90 » Sat Jun 21, 2008 3:47 pm

New dyno numbers with 5sp getrag 308hp/724tq :D
1992 reg cab W-350 5sp 12cm ex housing,pod's,3200rpm gov,and piston lift pump
oldcool90
fuel screw!!!!
 
Posts: 164
Joined: Sun Jun 03, 2007 1:50 pm
Location: terre haute In.
Top

PreviousNext

Return to Competition

Who is online

Users browsing this forum: No registered users and 15 guests