1410 front drive shaft

Sled-pulling, Drag results, Dyno results

Moderators: Greenleaf, KTA, BC847, Richie O

1410 front drive shaft

Postby cumminscloud » Wed Feb 23, 2011 8:14 am

been wanting to upgrade my front drive shaft ran into alot of problems andbody have a solution for this would like to go 1410 yokes is this possable thanks
User avatar
cumminscloud
fuel pin?
 
Posts: 5
Joined: Wed Jun 23, 2010 7:09 pm
Location: warren ohio

Re: 1410 front drive shaft

Postby BILTIT » Wed Feb 23, 2011 12:54 pm

This is the man to talk to-jesse.

http://www.highangledriveline.com/
Derek B.
2003 QuadCab, Tater 62/65 341cw, Smarty Touch SW9, Full Billet trans.
91.5 W250, coolertubz, HE351CW, PS IC, Alcans, GVOD, Valair DD, bags, crossover.
1974 Pontiac Ventura,best of 11.97 at 112 so far.
Aluminum heads and roller cam on the way.
User avatar
BILTIT
14mm rotor
 
Posts: 711
Joined: Wed Aug 11, 2010 1:29 pm
Location: Lloydminster, Saskatchewan

Re: 1410 front drive shaft

Postby cumminscloud » Wed Feb 23, 2011 8:01 pm

thank you
User avatar
cumminscloud
fuel pin?
 
Posts: 5
Joined: Wed Jun 23, 2010 7:09 pm
Location: warren ohio
Top

Re: 1410 front drive shaft

Postby KTA » Thu Feb 24, 2011 7:52 am

You can put up to a 1480 yoke on the ring and pinion end. The problem is the trasnfercase end. Getting a big CV joint is hard to come by.
Fleet of Junk: 1989 D350 627rwhp 1300 tq B-1/Hx60 twins, KTA pump/injectors, ported head, BIG fuel supply. 13.75@ 109.5mph 1/4: 1992 W350 Cab-chasis, 1993 W350 ext cab cust.370 inj Hx40/16cm 290rwhp hydroboost brakes,1984 D350 crew-cab another project.
User avatar
KTA
diesel guru/mod
 
Posts: 1855
Joined: Thu Jan 04, 2007 2:23 pm
Location: Shelby County, Ky
Top

Re: 1410 front drive shaft

Postby GLHS » Thu Feb 24, 2011 9:21 am

I put a 1410 on the D60 and used a 1350 on the transfercase side.

The weakest link is the D60 side.

If it's a 89-92 it is tiny. The 93s are bigger.
92 W250 ext cab, 5spd, SPS 62/71/14, ATS 3 piece, Banks 3G intake, Icebox CAI, DDP #4+, timing 1.95 mm, SB 4 puck FE, PDR fuel pin, Hellmann intercooler, Snow water/meth, 60# springs, stock long block, D80 3.54 w/disks, 455+/1005 uncorrected, 13.34@102 7-06; 472 fuel/520 water/meth uncorrected 5-08
GLHS
fuel screw!!!!
 
Posts: 273
Joined: Sat Jan 20, 2007 8:17 am
Location: Brighton, CO
Top

Re: 1410 front drive shaft

Postby rockjeep73 » Fri Feb 25, 2011 8:14 pm

On my brothers truck we went to a 1410 on the Dana 60 end and are still running the stock 1310 cv at the t-case, haven't had a problem with it at 900hp.
2000 QCLB 2500 4x4, 12.05 @ 111

89 D-250, In The Graveyard

89 W-250, Mostly Stock

http://www.SHSDiesel.com
rockjeep73
fuel screw!!!!
 
Posts: 114
Joined: Sun Dec 16, 2007 10:43 am
Location: Folsom, CA
Top

Re: 1410 front drive shaft

Postby ahale2772 » Wed Mar 02, 2011 8:40 am

Rockjeep, do you run the upgraded np205 output?...or maybe you dont run an np205?
84 CCLB W350 project
94' W350 Dually, Diesel, Auto 1080HP/1980FTlbs
User avatar
ahale2772
14mm rotor
 
Posts: 2353
Joined: Tue Jul 21, 2009 9:43 am
Location: massachusetts
Top

Re: 1410 front drive shaft

Postby rockjeep73 » Wed Mar 02, 2011 4:16 pm

We ran a stock 29 spline 205 and never had a problem with it at the 700hp level. With the last round of upgrades we went to a 271, 900+ hp now.
2000 QCLB 2500 4x4, 12.05 @ 111

89 D-250, In The Graveyard

89 W-250, Mostly Stock

http://www.SHSDiesel.com
rockjeep73
fuel screw!!!!
 
Posts: 114
Joined: Sun Dec 16, 2007 10:43 am
Location: Folsom, CA
Top


Return to Competition

Who is online

Users browsing this forum: No registered users and 11 guests