1stGen.org

THE place for 1st gens

Skip to content

205 transfer case yoke swap

How they work, how they don't work, and how to fix them

Moderators: Greenleaf, BC847, Richie O

Post a reply

205 transfer case yoke swap

Postby oldcool90 » Wed Mar 19, 2008 1:22 pm

Was wondering if the out put safts were the same from an auto to a 5sp transfer case? I might need to swap yokes if they are. Thanks Matt
1992 reg cab W-350 5sp 12cm ex housing,pod's,3200rpm gov,and piston lift pump
oldcool90
fuel screw!!!!
 
Posts: 164
Joined: Sun Jun 03, 2007 1:50 pm
Location: terre haute In.
Top

Postby bgilbert » Wed Mar 19, 2008 3:05 pm

Auto = sissy stuff. Getrag = beefy stuff ;) :P :lol: .
Bill Gilbert
85 D350 crew with 90 6BT intercooled Getrag 3.07's
93 D350 single cab Getrag 3.54's.
bgilbert
14mm rotor
 
Posts: 2253
Joined: Wed Jan 03, 2007 5:04 pm
Location: Terre Haute, Indiana
Top

Postby dpuckett » Wed Mar 19, 2008 8:05 pm

Are we talking front or rear? Why not just get a new yoke and be done with it?

DP
His- 93 W250 club cab LE, auto to Getrag conversion, piston lift pump, 3.54 LSD. 400k+
Hers- 04 QC 4x4. Built auto, Triple Dog, Air Dog. Funny Round truck that aint so quiet.
dpuckett
14mm rotor
 
Posts: 2196
Joined: Wed Jan 03, 2007 4:33 pm
Location: Perryville MO
Top

Postby oldcool90 » Thu Mar 20, 2008 1:32 pm

dpuckett wrote:Are we talking front or rear? Why not just get a new yoke and be done with it?

DP
Both,i am putin in a 5sp and the transfercase on the 5sp has the bad yokes.My auto transfercase on the other hand has perfect yokes.I dont want to use a speedy sleeve,so if they wont work i will weld them up and turn them down at my shop.Just was lookin for the easy way out ;)
1992 reg cab W-350 5sp 12cm ex housing,pod's,3200rpm gov,and piston lift pump
oldcool90
fuel screw!!!!
 
Posts: 164
Joined: Sun Jun 03, 2007 1:50 pm
Location: terre haute In.
Top

Postby MMiller » Sun Mar 30, 2008 7:07 pm

The driveshaft yokes will be the same. All first gens used 1410 joints to my knowledge. There is not yoke on the front output, its just a flat 4 bolt flange. I've never seen one of those wear out.....

Michael
1993 W250, 3.55, NV5600 , Con O, bosch 185's, 4" exhaust, Super 40, pump tweaks, ground pin, Smokehouse air intake, Hamilton Cam,
1985 D350, Crew Cab, 92 cummins and a 518. 47rh to be built and installed along with 3.55 LS Dana 80
MMiller
fuel screw!!!!
 
Posts: 391
Joined: Mon Jan 08, 2007 6:26 am
Location: Lenox Ia
Top
Post a reply

Return to Transmission

Who is online

Users browsing this forum: No registered users and 36 guests

Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group