1stGen.org

THE place for 1st gens

Skip to content

wheels

both inside and out

Moderators: Greenleaf, BC847, Richie O

Post a reply

Postby PToombs » Tue Jun 17, 2008 5:28 pm

KRB, should be on the 1st weekend in October. Was wondering where you were, I was trying to chat with more people. If you go to Cali again, can I ride in the suitcase? ;)

Jeff, didn't I mention the trailers? :grrr:

:jumpsmile:

I'd like to make it to the track this summer, if I get the damn thing put together! :bh:
pete

Just enough power to break everything behind the crankshaft.
User avatar
PToombs
14mm rotor
 
Posts: 11369
Joined: Sun Jan 07, 2007 6:13 pm
Location: Syracuse NY. Snow central!
Top

Postby RumbleFish » Tue Jun 17, 2008 7:38 pm

leave the cab off. just think of it as weight reduction. quicker and better mpg's ;)
User avatar
RumbleFish
14mm rotor
 
Posts: 2648
Joined: Thu Jan 11, 2007 1:19 pm
Location: Indiana
Top

Postby KRB64 » Wed Jun 18, 2008 3:07 am

PToombs wrote:KRB, should be on the 1st weekend in October. Was wondering where you were, I was trying to chat with more people. If you go to Cali again, can I ride in the suitcase? ;)



I'd like to see you sit still long enough to stay in a suitcase!

Besides, we're going to Texas this year I think, but not til November.
'92 W250 CC LE, auto, OD on shift, 3.54 limited; boost/PT pyro/tranny, oil temp, fuel press, tach; Bosch 190s, Ol' Smoky, 366 spring, full fuel, pull cable, 1/8" bump, synthetics, Borgeson, aFe, 16cm house, 4" pipe, AT cooler, ton shoes, ext reg...
KRB64
fuel screw!!!!
 
Posts: 88
Joined: Sat Feb 10, 2007 4:01 am
Location: Central Kentucky
Top

Postby PToombs » Wed Jun 18, 2008 5:15 pm

I bet it's still hotter than heck down there then!

Jeff, think this is enough weight?

Image
pete

Just enough power to break everything behind the crankshaft.
User avatar
PToombs
14mm rotor
 
Posts: 11369
Joined: Sun Jan 07, 2007 6:13 pm
Location: Syracuse NY. Snow central!
Top

Postby RumbleFish » Wed Jun 18, 2008 6:05 pm

prolly close. are those your bucket seats? nice!

on 2nd thought, you better take more weight off if your gonna run it naturally aspirated like that!
User avatar
RumbleFish
14mm rotor
 
Posts: 2648
Joined: Thu Jan 11, 2007 1:19 pm
Location: Indiana
Top

Postby GO OVRIT » Wed Jun 18, 2008 6:53 pm

RumbleFish wrote:prolly close. are those your bucket seats? nice!

:jumpsmile:
92 W250 ext cab 518, big sticks, a-1000, PDR HX40, 4" exhaust w/aeroturbine, pump tweaked, K&N filter Tims Cooler tubes and 3" i/c, gauges
GO OVRIT
14mm rotor
 
Posts: 554
Joined: Tue Nov 13, 2007 8:59 pm
Location: Gloucester Va.
Top

Postby PToombs » Thu Jun 19, 2008 5:42 pm

Nope, got a turbo from an 855 I'm gonna put on! :jumpsmile:
pete

Just enough power to break everything behind the crankshaft.
User avatar
PToombs
14mm rotor
 
Posts: 11369
Joined: Sun Jan 07, 2007 6:13 pm
Location: Syracuse NY. Snow central!
Top

Postby Richie O » Thu Jun 19, 2008 7:52 pm

Just steal that Dodge Dakota next door and put engine in there. :D
1989 W250 727, 3.07 L/S, S300, P/S Intercooler, Stans exaust, Pump adjustments, 127k miles,297 hp
1993 W250 extended cab, rag, 4.10 l/s, 6x16's, HTT 62/71/14 piston l/p, Isspro EV series tach, fuel pressure, boost, oil pres, water temp, volt, pryo, 132k/ 301 hp
1992 W250 with NV4500, 3.54's, 16cm 60mm GDS H1C, ground stock cone, Isspro tach, pryo, boost, fuel pressure, slow, rusty, dented,180k
User avatar
Richie O
Administrator
 
Posts: 4171
Joined: Sat May 17, 2008 9:01 pm
Location: New England
Top

Postby PToombs » Fri Jun 20, 2008 6:06 pm

Nice looking, huh? Hasn't run in about 6-7 years. I think the fuel pump is bad, among other things. I broke the rear drums off with a sledgehammer last summer so we could roll it around. Now the calipers are stuck on pretty good. :roll:
pete

Just enough power to break everything behind the crankshaft.
User avatar
PToombs
14mm rotor
 
Posts: 11369
Joined: Sun Jan 07, 2007 6:13 pm
Location: Syracuse NY. Snow central!
Top
Previous
Post a reply

Return to Body

Who is online

Users browsing this forum: No registered users and 23 guests

Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group
cron