1stGen.org

THE place for 1st gens

Skip to content

window molding

both inside and out

Moderators: Greenleaf, BC847, Richie O

Post a reply

window molding

Postby jacobwebb57 » Wed Jan 11, 2012 7:17 pm

Has anyone replaced the window crown belt molding (that is what mopar calls them) they are the lower seals on the door window. Mine are cracked and broke water just pours into them when it rains..my dodge dealer wants 250 for all of them im sure someone knows where to find them cheaper
91.5 4x4 5 speed, dennyt stage 2. ddp 50 horse injectors. glow shift boost, fuel pressure, egt, autometer tach, 60lb vavle spring, 3800 gov springs, 1 ton axles, custom intake, 4'' exaust, hx35w pump turned up 3 turns raptor pump, and 1/8 timing.. new injectors sooner or later
jacobwebb57
fuel screw!!!!
 
Posts: 77
Joined: Mon Dec 19, 2011 6:13 pm
Location: tiffin ohio
Top

Re: window molding

Postby ellis93 » Wed Jan 11, 2012 9:08 pm

JC Whitney has then
93 D250 ,5 speed,4.11s,k&n autometer tach pyro trans boost guages,GDS 60mm h1c 14cm,honed 5x10,hplp/reg,1/8 timing,M+H M2 fuel pin, tims cooler tubz
User avatar
ellis93
14mm rotor
 
Posts: 7761
Joined: Wed Feb 17, 2010 3:16 pm
Location: lucedale,mississippi
Top

Re: window molding

Postby Tacoclaw » Wed Jan 11, 2012 9:19 pm

http://www.jimsautoparts.com/truck_weatherstripping.htm

http://www.rustrepair.com/PARTS_PAGE.HT ... EPU.81.WEA
1990 W250 4x4
Rattles, growls, whistles, and whines.
User avatar
Tacoclaw
14mm rotor
 
Posts: 4108
Joined: Wed Mar 11, 2009 7:50 am
Location: Cheshire, OH
Top

Re: window molding

Postby jacobwebb57 » Thu Jan 12, 2012 2:07 pm

thanks guys
91.5 4x4 5 speed, dennyt stage 2. ddp 50 horse injectors. glow shift boost, fuel pressure, egt, autometer tach, 60lb vavle spring, 3800 gov springs, 1 ton axles, custom intake, 4'' exaust, hx35w pump turned up 3 turns raptor pump, and 1/8 timing.. new injectors sooner or later
jacobwebb57
fuel screw!!!!
 
Posts: 77
Joined: Mon Dec 19, 2011 6:13 pm
Location: tiffin ohio
Top

Re: window molding

Postby PToombs » Thu Jan 12, 2012 6:11 pm

That Jims auto parts is pricey! There is a thread on here that lists a part number at Rock Auto. I think you can get all 4 for less than $50.
pete

Just enough power to break everything behind the crankshaft.
User avatar
PToombs
14mm rotor
 
Posts: 11367
Joined: Sun Jan 07, 2007 6:13 pm
Location: Syracuse NY. Snow central!
Top

Re: window molding

Postby jacobwebb57 » Thu Jan 12, 2012 6:24 pm

i just ordered all 4 from jcw for 46 bucks..better then 250 at dealership :D
91.5 4x4 5 speed, dennyt stage 2. ddp 50 horse injectors. glow shift boost, fuel pressure, egt, autometer tach, 60lb vavle spring, 3800 gov springs, 1 ton axles, custom intake, 4'' exaust, hx35w pump turned up 3 turns raptor pump, and 1/8 timing.. new injectors sooner or later
jacobwebb57
fuel screw!!!!
 
Posts: 77
Joined: Mon Dec 19, 2011 6:13 pm
Location: tiffin ohio
Top

Re: window molding

Postby kbhblazer » Sat Apr 14, 2012 12:05 pm

^Thanks been looking for them
kbhblazer
fuel pin?
 
Posts: 13
Joined: Sat Apr 14, 2012 11:23 am
Top

Re: window molding

Postby Mark Nixon » Mon May 21, 2012 10:08 pm

PToombs wrote:That Jims auto parts is pricey! There is a thread on here that lists a part number at Rock Auto. I think you can get all 4 for less than $50.

Jim's huh? :lol:
If you only knew the HALF of it. :roll:

Mark.
Mark Nixon
 
Top

Re: window molding

Postby CumminsPower59 » Tue May 22, 2012 4:12 am

I just put new ones on the 92, got four of them from rock auto for $34 bucks...

FAIRCHILD Part # KD2003.
Ike

91 W350 SRW, 3.07's, NV4500, 370's, THD LPPP, Super HX40, 2nd gen IC swap, BHAF, Isspro's, 2" lift, 285's on 3rd gen 17"'s.
04 VW Jetta Wagon TDI 5speed
CumminsPower59
14mm rotor
 
Posts: 3203
Joined: Mon Feb 25, 2008 8:04 am
Location: The Hawkeye State of 'Murica!
Top
Post a reply

Return to Body

Who is online

Users browsing this forum: No registered users and 19 guests

Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group