1stGen.org

THE place for 1st gens

Skip to content

guess my hp

Sled-pulling, Drag results, Dyno results

Moderators: Greenleaf, KTA, BC847, Richie O

Post a reply

Re: guess my hp

Postby RCCUMMINS89 » Fri May 24, 2013 7:07 pm

Well............damn, I was at least close on the torque.

Apparently I was damn near 500 rpms off on where it was going to make it.

Good number though, Do you have the sheet so we can see the curve?
89 RC on shortened 92 diesel frame - NV4500 w/dual disc/4.10s on 37s. - Self built pump, "hot screw", lots of timing, True high volume low pressure lift pump, 62fmw/68/.7gated, 77lpm SAC Inj., Studs/O-rings,- 423/1220 Mustang - 11/16/2013 http://www.TheHungryDiesel.com full line dealer, if you don't see it please ask.
RCCUMMINS89
14mm rotor
 
Posts: 4826
Joined: Mon Oct 03, 2011 4:19 pm
Location: Spirit Lake, ID
Top

Re: guess my hp

Postby dazedandconfused » Fri May 24, 2013 7:19 pm

I wasn't far off.
Big Andy
1983 Dodge D150 that has been repowered with a 93 Cummins/518 running gear AKA The Ugly Duck! I would much rather build them then buy them.[
User avatar
dazedandconfused
14mm rotor
 
Posts: 6116
Joined: Thu Apr 05, 2007 6:25 pm
Location: Walton, Kentucky
Top

Re: guess my hp

Postby turboram » Fri May 24, 2013 8:03 pm

Torque would be way better with a good motor
turboram
fuel screw!!!!
 
Posts: 207
Joined: Sun Oct 21, 2012 6:01 am
Location: nw ohio
Top

Re: guess my hp

Postby RCCUMMINS89 » Fri May 24, 2013 8:17 pm

Good point.
89 RC on shortened 92 diesel frame - NV4500 w/dual disc/4.10s on 37s. - Self built pump, "hot screw", lots of timing, True high volume low pressure lift pump, 62fmw/68/.7gated, 77lpm SAC Inj., Studs/O-rings,- 423/1220 Mustang - 11/16/2013 http://www.TheHungryDiesel.com full line dealer, if you don't see it please ask.
RCCUMMINS89
14mm rotor
 
Posts: 4826
Joined: Mon Oct 03, 2011 4:19 pm
Location: Spirit Lake, ID
Top

Re: guess my hp

Postby Sutter1stgen » Fri May 24, 2013 9:57 pm

PToombs wrote:Sutters 1st guess was closest, he gets an all expenses paid (by him) trip to someplace where he can drink beer and brag about it! 8)
Congrats Sutter1stgen!


YYYYYYYYEEEEEEEESSSSSSSS!!!!

Well as I've gotten older, I think the safest choice would be for me to take the trip to my kitchen. Crack open a budlite lime ( they were left overs from wife's Bonco group), and proceed to to brag to my own reflection in the window. Lol

The wife would probably get a little unnerved if I awoke her to tell about dyno numbers at this point. Especially someone else's. Hahaha.
Eric

91'w250 with a new pump. This one doesn't chase itself around in a circle.
Sutter1stgen
14mm rotor
 
Posts: 512
Joined: Wed Sep 12, 2012 8:18 pm
Location: Northern California.
Top

Re: guess my hp

Postby PToombs » Sat May 25, 2013 5:56 pm

That would be living dangerously, BTDT! ;) :lol:
pete

Just enough power to break everything behind the crankshaft.
User avatar
PToombs
14mm rotor
 
Posts: 11355
Joined: Sun Jan 07, 2007 6:13 pm
Location: Syracuse NY. Snow central!
Top
Previous
Post a reply

Return to Competition

Who is online

Users browsing this forum: No registered users and 0 guests

Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group