![Image](http://i211.photobucket.com/albums/bb122/RESWORDS/kdpdamage.jpg)
There are kits on the market to fix this problem or you can do it yourself, I'm a cheap ass so I went the DIY route.
I already had the front of my truck off for some other work but you can do this with just removing the radiator.
![Image](http://i211.photobucket.com/albums/bb122/RESWORDS/01-5.jpg)
First you need to remove the belt, then go after the four bolts holding the fan support to the block, I find it easier to remove the six bolts that hold the fan pulley to the shaft, slid the pulley forward so you have room to get to the bottom bolt, and take it off as one assembly. Here the six bolt have been removed and the pulley moved toward the front of the truck for access.
![Image](http://i211.photobucket.com/albums/bb122/RESWORDS/03-3.jpg)
And here is the front of the engine with the whole assembly gone
![Image](http://i211.photobucket.com/albums/bb122/RESWORDS/04-3.jpg)
Next we need to go after the crank pulley, its just four 15mm bolts. The easiest way to remove them is with a impact. If not you will need to keep the engine from rotating some how while you go at the with a 1/2' ratchet. Also go ahead and remove the oil fill tube. Un-bolt the mounting bracket at the head and then rotate th whole assembly counter-clockwise to unscrew it.
![Image](http://i211.photobucket.com/albums/bb122/RESWORDS/05-3.jpg)
Gone! Now start removing the 20 10mm bolts that hold the cover on, keep track because there are two lengths.
![Image](http://i211.photobucket.com/albums/bb122/RESWORDS/07-3.jpg)
Here is were you should be at! I put a red box around the area we will be concentrating on.
![Image](http://i211.photobucket.com/albums/bb122/RESWORDS/08-2.jpg)
Here is a close up, mine is still in place and has not moved. Yours may or may not be, go ahead and take a punch and hammer and tap it till it sits flush with the case.
![Image](http://i211.photobucket.com/albums/bb122/RESWORDS/pin.jpg)
Now we are going to tab it. I got this solution from BC847, Thanks David!!! Remove the bolt next to the pin, then take a coat hanger and cut a small piece. Using some pliers bend up your piece of coat hanger to resemble this shape. Make sure the loop is a snug fit around the bolt.
![Image](http://i211.photobucket.com/albums/bb122/RESWORDS/09-1.jpg)
Now with your tab in place replace the bolt, put some red thread locking compound on the bolt and torque it to 18 ft/lbs.
![Image](http://i211.photobucket.com/albums/bb122/RESWORDS/10-1.jpg)
It would be a good time also now to remove the rest of the case bolts and put thread lock on them also, one of mine was not even snug any more... That would have been as bad as the KDP! There are two hidden behind the cam gear, don't forget them! You will have to rotate the engine till you can access them through the holes in the gear. I circled them in red here.
![Image](http://i211.photobucket.com/albums/bb122/RESWORDS/P1010057.jpg)
Now its time to replace the cover, make sure all the old gasket material is removed and everything is REALLY clean. Then grab some RTV and run a bead around the lip and around all the bolt holes, you want NO gaps. Replace the cover and snug the bolts down. This is the RTV I use.
![Image](http://i211.photobucket.com/albums/bb122/RESWORDS/51WPE5WCMXL_SS500_.jpg)
Finally simply replace everything you took apart and enjoy your truck knowing that a 1/4" piece of steal wont kill your pride and joy!