1stGen.org

THE place for 1st gens

Skip to content

Fuel in oil, IP, LP?

How the engine works

Moderators: Greenleaf, KTA, BC847, Richie O

Post a reply

Re: Fuel in oil, IP, LP?

Postby MMiller » Fri May 31, 2013 5:24 pm

The injection pump shaft has some play up and down, and I presume it needs the bushing replaced. The KDP was taken care of a few years ago, but the front cover between the block leaks, as does the side cover. Its all getting done along with some cowl cracks.
1993 W250, 3.55, NV5600 , Con O, bosch 185's, 4" exhaust, Super 40, pump tweaks, ground pin, Smokehouse air intake, Hamilton Cam,
1985 D350, Crew Cab, 92 cummins and a 518. 47rh to be built and installed along with 3.55 LS Dana 80
MMiller
fuel screw!!!!
 
Posts: 391
Joined: Mon Jan 08, 2007 6:26 am
Location: Lenox Ia
Top

Re: Fuel in oil, IP, LP?

Postby PToombs » Fri May 31, 2013 5:33 pm

Good time to do a cam! :mrgreen:
pete

Just enough power to break everything behind the crankshaft.
User avatar
PToombs
14mm rotor
 
Posts: 11369
Joined: Sun Jan 07, 2007 6:13 pm
Location: Syracuse NY. Snow central!
Top

Re: Fuel in oil, IP, LP?

Postby MMiller » Fri May 31, 2013 5:44 pm

PToombs wrote:Good time to do a cam! :mrgreen:


Send me one, I'll stick it in and make payments......
1993 W250, 3.55, NV5600 , Con O, bosch 185's, 4" exhaust, Super 40, pump tweaks, ground pin, Smokehouse air intake, Hamilton Cam,
1985 D350, Crew Cab, 92 cummins and a 518. 47rh to be built and installed along with 3.55 LS Dana 80
MMiller
fuel screw!!!!
 
Posts: 391
Joined: Mon Jan 08, 2007 6:26 am
Location: Lenox Ia
Top

Re: Fuel in oil, IP, LP?

Postby PToombs » Fri May 31, 2013 6:13 pm

I got one from a 4b, you're on your own for # 5 and 6. ;)




Why not put it on the card and make payments? You won't like my interest rates or the collector. :twisted:
pete

Just enough power to break everything behind the crankshaft.
User avatar
PToombs
14mm rotor
 
Posts: 11369
Joined: Sun Jan 07, 2007 6:13 pm
Location: Syracuse NY. Snow central!
Top

Re: Fuel in oil, IP, LP?

Postby RCCUMMINS89 » Fri May 31, 2013 6:28 pm

I'll take payments............ but I'd need about 600 up front :lol:
89 RC on shortened 92 diesel frame - NV4500 w/dual disc/4.10s on 37s. - Self built pump, "hot screw", lots of timing, True high volume low pressure lift pump, 62fmw/68/.7gated, 77lpm SAC Inj., Studs/O-rings,- 423/1220 Mustang - 11/16/2013 http://www.TheHungryDiesel.com full line dealer, if you don't see it please ask.
RCCUMMINS89
14mm rotor
 
Posts: 4826
Joined: Mon Oct 03, 2011 4:19 pm
Location: Spirit Lake, ID
Top

Re: Fuel in oil, IP, LP?

Postby MMiller » Fri May 31, 2013 7:32 pm

I gotta make every $$ count for a while. I already have have enough credit card payments as it is, and I kinda have to keep what credit I do have open for emergencies, and unexpected expenses. It sucks having to be grown up and all responsible and such...:(
1993 W250, 3.55, NV5600 , Con O, bosch 185's, 4" exhaust, Super 40, pump tweaks, ground pin, Smokehouse air intake, Hamilton Cam,
1985 D350, Crew Cab, 92 cummins and a 518. 47rh to be built and installed along with 3.55 LS Dana 80
MMiller
fuel screw!!!!
 
Posts: 391
Joined: Mon Jan 08, 2007 6:26 am
Location: Lenox Ia
Top

Re: Fuel in oil, IP, LP?

Postby bgilbert » Fri May 31, 2013 7:42 pm

Cams are for gassers anyways. lol
Bill Gilbert
85 D350 crew with 90 6BT intercooled Getrag 3.07's
93 D350 single cab Getrag 3.54's.
bgilbert
14mm rotor
 
Posts: 2253
Joined: Wed Jan 03, 2007 5:04 pm
Location: Terre Haute, Indiana
Top

Re: Fuel in oil, IP, LP?

Postby Mark Nixon » Fri May 31, 2013 8:02 pm

bgilbert wrote:Cams are for gassers anyways. lol

I agree!
I know I don't need a "CAM" to pass gas. :lol:

Mark.
Mark Nixon
 
Top
Previous
Post a reply

Return to Engine

Who is online

Users browsing this forum: No registered users and 21 guests

Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group
cron