1stGen.org

THE place for 1st gens

Skip to content

Big Red Pile 91 W350 Build Thread

Cummins Conversion & Builds

Moderators: Greenleaf, BC847, Richie O

Post a reply

Re: Big Red Pile 91 W350 Build Thread

Postby PToombs » Thu Jun 20, 2013 5:00 pm

It works great 90% of the time, it's when backing a trailer up any grade it really sucks! :bounce:
pete

Just enough power to break everything behind the crankshaft.
User avatar
PToombs
14mm rotor
 
Posts: 11370
Joined: Sun Jan 07, 2007 6:13 pm
Location: Syracuse NY. Snow central!
Top

Re: Big Red Pile 91 W350 Build Thread

Postby RCCUMMINS89 » Thu Jun 20, 2013 5:17 pm

Mine .................ya just feel like ya never know when it's gonna grab. If it warms up 30 degrees outside it'll grab a 1/2" lower to the floor.
89 RC on shortened 92 diesel frame - NV4500 w/dual disc/4.10s on 37s. - Self built pump, "hot screw", lots of timing, True high volume low pressure lift pump, 62fmw/68/.7gated, 77lpm SAC Inj., Studs/O-rings,- 423/1220 Mustang - 11/16/2013 http://www.TheHungryDiesel.com full line dealer, if you don't see it please ask.
RCCUMMINS89
14mm rotor
 
Posts: 4826
Joined: Mon Oct 03, 2011 4:19 pm
Location: Spirit Lake, ID
Top

Re: Big Red Pile 91 W350 Build Thread

Postby CumminsPower59 » Thu Jun 27, 2013 3:39 pm

Clutch came in yesterday, hopefully this weekend I can pull everything apart and get it swapped in. On another note, got a miss at high rpms (2500+), and its still doing the wandering idle. Drove it to work again today, if it wasn't for the bone jarring ride, it would be quite bearable...
Ike

91 W350 SRW, 3.07's, NV4500, 370's, THD LPPP, Super HX40, 2nd gen IC swap, BHAF, Isspro's, 2" lift, 285's on 3rd gen 17"'s.
04 VW Jetta Wagon TDI 5speed
CumminsPower59
14mm rotor
 
Posts: 3203
Joined: Mon Feb 25, 2008 8:04 am
Location: The Hawkeye State of 'Murica!
Top

Re: Big Red Pile 91 W350 Build Thread

Postby RCCUMMINS89 » Thu Jun 27, 2013 3:43 pm

Wandering idle.............miss high rpm. ? Air? something off internally of the pump?
89 RC on shortened 92 diesel frame - NV4500 w/dual disc/4.10s on 37s. - Self built pump, "hot screw", lots of timing, True high volume low pressure lift pump, 62fmw/68/.7gated, 77lpm SAC Inj., Studs/O-rings,- 423/1220 Mustang - 11/16/2013 http://www.TheHungryDiesel.com full line dealer, if you don't see it please ask.
RCCUMMINS89
14mm rotor
 
Posts: 4826
Joined: Mon Oct 03, 2011 4:19 pm
Location: Spirit Lake, ID
Top

Re: Big Red Pile 91 W350 Build Thread

Postby CumminsPower59 » Thu Jun 27, 2013 3:53 pm

Probably the pump. Don't really care too much about it anymore, got another pump on the way to try out....
Ike

91 W350 SRW, 3.07's, NV4500, 370's, THD LPPP, Super HX40, 2nd gen IC swap, BHAF, Isspro's, 2" lift, 285's on 3rd gen 17"'s.
04 VW Jetta Wagon TDI 5speed
CumminsPower59
14mm rotor
 
Posts: 3203
Joined: Mon Feb 25, 2008 8:04 am
Location: The Hawkeye State of 'Murica!
Top

Re: Big Red Pile 91 W350 Build Thread

Postby ellis93 » Thu Jun 27, 2013 6:18 pm

What clutch did you go with?
93 D250 ,5 speed,4.11s,k&n autometer tach pyro trans boost guages,GDS 60mm h1c 14cm,honed 5x10,hplp/reg,1/8 timing,M+H M2 fuel pin, tims cooler tubz
User avatar
ellis93
14mm rotor
 
Posts: 7762
Joined: Wed Feb 17, 2010 3:16 pm
Location: lucedale,mississippi
Top

Re: Big Red Pile 91 W350 Build Thread

Postby CumminsPower59 » Thu Jun 27, 2013 6:31 pm

Same one you got...
Ike

91 W350 SRW, 3.07's, NV4500, 370's, THD LPPP, Super HX40, 2nd gen IC swap, BHAF, Isspro's, 2" lift, 285's on 3rd gen 17"'s.
04 VW Jetta Wagon TDI 5speed
CumminsPower59
14mm rotor
 
Posts: 3203
Joined: Mon Feb 25, 2008 8:04 am
Location: The Hawkeye State of 'Murica!
Top

Re: Big Red Pile 91 W350 Build Thread

Postby ellis93 » Thu Jun 27, 2013 7:18 pm

You'll like it,it's really smooth.....like stock with a firm pedal,no pudding pedal ;)
93 D250 ,5 speed,4.11s,k&n autometer tach pyro trans boost guages,GDS 60mm h1c 14cm,honed 5x10,hplp/reg,1/8 timing,M+H M2 fuel pin, tims cooler tubz
User avatar
ellis93
14mm rotor
 
Posts: 7762
Joined: Wed Feb 17, 2010 3:16 pm
Location: lucedale,mississippi
Top

Re: Big Red Pile 91 W350 Build Thread

Postby CumminsPower59 » Thu Jun 27, 2013 7:34 pm

Right on.

A different view of "The Pile"...
Image
Last edited by CumminsPower59 on Tue Sep 09, 2014 10:45 am, edited 1 time in total.
Ike

91 W350 SRW, 3.07's, NV4500, 370's, THD LPPP, Super HX40, 2nd gen IC swap, BHAF, Isspro's, 2" lift, 285's on 3rd gen 17"'s.
04 VW Jetta Wagon TDI 5speed
CumminsPower59
14mm rotor
 
Posts: 3203
Joined: Mon Feb 25, 2008 8:04 am
Location: The Hawkeye State of 'Murica!
Top

Re: Big Red Pile 91 W350 Build Thread

Postby PToombs » Fri Jun 28, 2013 5:38 pm

Is it only you that has a problem parking between the lines? It looks like it! :lol:

And it looks like the box has snow in it. lol
pete

Just enough power to break everything behind the crankshaft.
User avatar
PToombs
14mm rotor
 
Posts: 11370
Joined: Sun Jan 07, 2007 6:13 pm
Location: Syracuse NY. Snow central!
Top

Re: Big Red Pile 91 W350 Build Thread

Postby RCCUMMINS89 » Fri Jun 28, 2013 6:07 pm

:lol:
89 RC on shortened 92 diesel frame - NV4500 w/dual disc/4.10s on 37s. - Self built pump, "hot screw", lots of timing, True high volume low pressure lift pump, 62fmw/68/.7gated, 77lpm SAC Inj., Studs/O-rings,- 423/1220 Mustang - 11/16/2013 http://www.TheHungryDiesel.com full line dealer, if you don't see it please ask.
RCCUMMINS89
14mm rotor
 
Posts: 4826
Joined: Mon Oct 03, 2011 4:19 pm
Location: Spirit Lake, ID
Top

Re: Big Red Pile 91 W350 Build Thread

Postby CumminsPower59 » Fri Jun 28, 2013 6:13 pm

I park however I want...as I am the only one who drove in yesterday...everyone else rode thier Harleys. Never got around to painting the inside of the box yet....
Ike

91 W350 SRW, 3.07's, NV4500, 370's, THD LPPP, Super HX40, 2nd gen IC swap, BHAF, Isspro's, 2" lift, 285's on 3rd gen 17"'s.
04 VW Jetta Wagon TDI 5speed
CumminsPower59
14mm rotor
 
Posts: 3203
Joined: Mon Feb 25, 2008 8:04 am
Location: The Hawkeye State of 'Murica!
Top

Re: Big Red Pile 91 W350 Build Thread

Postby 1STGENFARMBOY » Sat Jun 29, 2013 7:27 am

don't you guys know that lines are just a suggestion......go to your local walmart and see for yourself.
93 W250 STD CAB, AUTO 3.55, GAUGES, 80HP DDP STICKS, DENNY T ,16CM HOUSING, 60MM GILLETT, VE MAXED,BHAF, BHFF, 366 SPRING,P/S INTERCOOLER, TIMS COOLER TUBS, TIMMING 1/8 BUMP,4in TURBO BACK TO DUEL 5IN STACKS,33 12.50 BFG, HOLLEY BLACK, CONVERTER COOMING.
User avatar
1STGENFARMBOY
14mm rotor
 
Posts: 2089
Joined: Mon Sep 28, 2009 2:23 pm
Location: PITTSBURG ILL
Top

Re: Big Red Pile 91 W350 Build Thread

Postby RCCUMMINS89 » Sat Jun 29, 2013 9:03 am

Like the stop signs that have the white ring around them? Those are optional......................
89 RC on shortened 92 diesel frame - NV4500 w/dual disc/4.10s on 37s. - Self built pump, "hot screw", lots of timing, True high volume low pressure lift pump, 62fmw/68/.7gated, 77lpm SAC Inj., Studs/O-rings,- 423/1220 Mustang - 11/16/2013 http://www.TheHungryDiesel.com full line dealer, if you don't see it please ask.
RCCUMMINS89
14mm rotor
 
Posts: 4826
Joined: Mon Oct 03, 2011 4:19 pm
Location: Spirit Lake, ID
Top

Re: Big Red Pile 91 W350 Build Thread

Postby PToombs » Sun Jun 30, 2013 5:03 pm

RC, that don't fly with the cop. Just letting you know. ;)
pete

Just enough power to break everything behind the crankshaft.
User avatar
PToombs
14mm rotor
 
Posts: 11370
Joined: Sun Jan 07, 2007 6:13 pm
Location: Syracuse NY. Snow central!
Top
PreviousNext
Post a reply

Return to Conversions & Builds

Who is online

Users browsing this forum: No registered users and 3 guests

Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group