1stGen.org

THE place for 1st gens

Skip to content

4 inch 90 elbo

How to make it go fast

Moderators: Greenleaf, KTA, BC847, Richie O

Post a reply

4 inch 90 elbo

Postby skilletky » Sat Nov 21, 2009 8:40 am

i can get these for $20 a piece from our local truck shop. they are cheaper in price from what i have seen on the inter net. if any one needs some i can get them for ya and ship them to ya. it will be how ever many ya want plus shipping

Image
92 d350, arp's, orings, 150lb springs, 4200 gsk ,ground pin ,64/71/14 ,ddp inj's, ats manifold, tim's tubez, ats trans, FASS, locker, timing + a tooth, bcdd intake

2001 2wd rclb dually 5sp, smarty, Bluechip FMS, TS MVP, 57/75 twins, stainless diesel pipe kit, valair clutch, airdog 150, DFI SAC 7x.014's, cheap a$$ intake, ARP studs, oringed head, CPP 115# springs
User avatar
skilletky
14mm rotor
 
Posts: 1070
Joined: Thu Jan 10, 2008 5:49 pm
Location: northern ky
Top

Postby PToombs » Sat Nov 21, 2009 7:37 pm

Good price, and that's the big bend too! 8)
pete

Just enough power to break everything behind the crankshaft.
User avatar
PToombs
14mm rotor
 
Posts: 11369
Joined: Sun Jan 07, 2007 6:13 pm
Location: Syracuse NY. Snow central!
Top

Postby Richie O » Sat Nov 21, 2009 7:42 pm

No toes. :flower:
1989 W250 727, 3.07 L/S, S300, P/S Intercooler, Stans exaust, Pump adjustments, 127k miles,297 hp
1993 W250 extended cab, rag, 4.10 l/s, 6x16's, HTT 62/71/14 piston l/p, Isspro EV series tach, fuel pressure, boost, oil pres, water temp, volt, pryo, 132k/ 301 hp
1992 W250 with NV4500, 3.54's, 16cm 60mm GDS H1C, ground stock cone, Isspro tach, pryo, boost, fuel pressure, slow, rusty, dented,180k
User avatar
Richie O
Administrator
 
Posts: 4171
Joined: Sat May 17, 2008 9:01 pm
Location: New England
Top

Postby RumbleFish » Sat Nov 21, 2009 7:47 pm

steel toes. better safe than sorry :safe:
User avatar
RumbleFish
14mm rotor
 
Posts: 2648
Joined: Thu Jan 11, 2007 1:19 pm
Location: Indiana
Top

Postby skilletky » Sun Nov 22, 2009 8:07 am

i was waiting for some one to say something about the toes. that is their small radius bend according to the parts guy.
92 d350, arp's, orings, 150lb springs, 4200 gsk ,ground pin ,64/71/14 ,ddp inj's, ats manifold, tim's tubez, ats trans, FASS, locker, timing + a tooth, bcdd intake

2001 2wd rclb dually 5sp, smarty, Bluechip FMS, TS MVP, 57/75 twins, stainless diesel pipe kit, valair clutch, airdog 150, DFI SAC 7x.014's, cheap a$$ intake, ARP studs, oringed head, CPP 115# springs
User avatar
skilletky
14mm rotor
 
Posts: 1070
Joined: Thu Jan 10, 2008 5:49 pm
Location: northern ky
Top
Post a reply

Return to The good stuff

Who is online

Users browsing this forum: No registered users and 50 guests

Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group
cron